HP ProLiant DL160se HP ProLiant DL160se G6 Server Maintenance and Service Guid - Page 50

Removal and replacement procedures, Removing the Hot-plug Hard Drive Assembly

Get HP ProLiant DL160se - G6 Server PDF manuals and user guides View all HP ProLiant DL160se manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

To remove the hot-plug hard drive: 1. Press the hard disk carrier button to release the ejector lever. 2. Use the HDD carrier latch to pull the drive out of the cage. Make sure to support the drive when pulling it out of the cage. 3. Pull the hard drive assembly out of the drive bay. Figure 16 Removing the Hot-plug Hard Drive Assembly To install the hot-plug hard drive: 1. Press the release tabs, and then pull the hard drive blank out of the chassis. Figure 17 Removing the Hot-plug Hard Drive Blank IMPORTANT: Do not discard the hard drive blank. If the drive is removed in the future, you must reinstall the hard drive blank to maintain proper system airflow. 2. Install a hard drive. a. Push the hard drive assembly into the drive bay until it stops. Removal and replacement procedures 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Removal and replacement procedures
50
To remove the hot-plug hard drive:
1.
Press the hard disk carrier button to release the ejector lever.
2.
Use the HDD carrier latch to pull the drive out of the cage.
Make sure to support the drive when pulling it out of the cage.
3.
Pull the hard drive assembly out of the drive bay.
Figure 16
Removing the Hot-plug Hard Drive Assembly
To install the hot-plug hard drive:
1.
Press the release tabs, and then pull the hard drive blank out of the chassis.
Figure 17
Removing the Hot-plug Hard Drive Blank
IMPORTANT:
Do not discard the hard drive blank. If the drive is removed in the future, you must
reinstall the hard drive blank to maintain proper system airflow.
2.
Install a hard drive.
a.
Push the hard drive assembly into the drive bay until it stops.