HP ProLiant SL390s HP ProLiant SL390s G7 2U half width Server Installation She
HP ProLiant SL390s - G7 Server Manual
 |
View all HP ProLiant SL390s manuals
Add to My Manuals
Save this manual to your list of manuals |
HP ProLiant SL390s manual content summary:
- HP ProLiant SL390s | HP ProLiant SL390s G7 2U half width Server Installation She - Page 1
and detailed procedures relating to installation of options, refer to any installation instructions that came with the option, as well as the HP ProLiant SL390s G7 2U half width Server Maintenance and Service Guide. • For safety information, regulatory notices, and detailed procedures related to the - HP ProLiant SL390s | HP ProLiant SL390s G7 2U half width Server Installation She - Page 2
2 GPU shelf DIMM slots are structured to ensure proper installation. If you insert a DIMM but it does not fit easily into the slot, you may have inserted it incorrectly. Reverse the orientation of the DIMM and insert it again. Installing the Processor The HP ProLiant SL390s server supports Intel
-
1 -
2
 |
 |
HP ProLiant SL390s G7 2U
half width Server
Installation Sheet
Part number: 614093-001
June 2010 (First Edition)
Identifying Server Components
Front Panel Components
SL390s 2U Server Front Panel Components
Figure 1
Front panel components of the s6500 chassis with
4 SL390s 2U servers
Item
Description
1
VGA port
2
Serial port
3
SFP PLUS connector
4
QSFP
5
NIC1/ iLO3 connector
6
NIC2
connector
7
USB connectors
8
UID LED/SW
9
HDD1
10
HDD2
11
Front PCIe bracket (LP slot)
12
Power LED/SW
13
HDD3
14
HDD4
15
iLO3 network port
Rear Panel Components
Figure 2
Rear panel components of the s6500 chassis with
4 SL390s 2U servers
Item
Description
1
Power Supply 1
2
Power Supply 2
3
Power Supply 3
4
Power Supply 4
Item
Description
5
UID LED
6
APM connector
7
Fan 1
8
Fan 2
9
Fan 3
10
Fan 4
11
Fan 5
12
Fan 6
13
Fan 7
14
Fan 8
Server Configuration Resources
In addition to this Installation Sheet, other resources are available for more
information regarding the configuration and maintenance of your server:
•
For safety information and detailed procedures relating to installation
of options, refer to any installation instructions that came with the
option, as well as the
HP ProLiant SL390s G7 2U half width Server
Maintenance and Service Guide
.
•
For safety information, regulatory notices, and detailed procedures
related to the rest of the steps listed in the “Configuring the Server”
section, refer to the relevant chapter of the
HP ProLiant SL390s G7 2U
half width Server User Guide
.
•
You can also access additional information and documentation from the
HP website at
.
Server Configuration Overview
The steps listed below give an overview of the necessary setup procedures
for preparing the HP ProLiant SL390s Server for operation:
1.
Connect the AC power cord and peripheral devices.
2.
Power up the server.
3.
Press “F9” to enter BIOS setup.
4.
Note the server BIOS version.
5.
Verify the server BIOS version against the latest BIOS version listed for
this server on the HP website:
.
6.
If you do not have the latest BIOS, update the BIOS now. Refer to the
HP
ProLiant SL390s G7 2U half width Server User Guide
available on the
HP website:
.
7.
Install a supported operating system of your choice. For detailed
procedures, refer to the documentation provided by the operating system
vendor. For a list of operating systems supported by your ProLiant server,
go to
.
Pre- and Post-installation
Procedures
When installing additional options in your HP ProLiant SL390s G7 2U half
width server, observe the following procedures:
Pre-installation procedures
1.
Turn off the server and all the peripherals connected to it.
2.
Remove the server from the chassis by following the procedure
described later in the “Removing the server” section.
Post-installation procedures
1.
Be sure all components are installed according to the described
step-by-step instructions.
2.
Check to make sure you have not left loose tools or parts inside
the server.
3.
Reinstall the PCI riser, peripherals, and system cables that you
have removed.
4.
Reinstall the server into the chassis.
5.
Connect all external cables to the system.
6.
Press the power button on the front panel to turn on the server.
Removing the Server
You need to remove the server from the chassis before you can remove or
replace a server component.
To remove server:
1.
Press the latch to release the handle.
2.
Rotate the handle to disengage the power connector.
3.
Extend the server from the chassis until the release latch catches.
4.
Firmly holding the server, press the release button.
5.
Remove the server from chassis.
6.
Install the server blank in the server slot.
Figure 3
Removing the SL390s left server
Figure 4
Removing the SL390s right server
Installing the Hard Disk Drive
One SL390s 2U server tray can accommodate up to 6 SFF hard disk drives
or SSDs, 2 non-hotplug SFF hard disk drives or SSDs on a quick release
carrier attached internally to the tray, and 4 SFF hotplug hard disk drives or
SSDs on the front of the tray. One chassis can accommodate 4 2U server
trays for up to 24 SFF hard disk drives or SSDs. The server supports both
SAS/SATA hard disk drives and SSDs.
CAUTION:
Drives can be damaged by static electricity. Before
handling drives, touch an unpainted metal surface to discharge
static electricity.
To install 2 non-hotplug SFF hard disk drives or SSDs on quick release
carriers to the tray:
Figure 5
Installing the non-hotplug SFF hard disk drives or SSDs on quick
release carriers to the tray
To install 4 SFF hotplug hard disk drives or SSDs on hotplug driver carriers
on the front of the tray:
1.
Insert the HDD into the chassis.
2.
Rotate the tray handle to lock the power connector.
Figure 6
Installing the hotplug hard disk drives or SSDs on hotplug driver
carrier on the front of the tray
Installing the Memory Module
The following guidelines must be followed when memory modules are
being added or replaced:
•
Support 12 DDR3 240-pin RDIMM (SR, DR, QR) or UDIMM (SR, DR)
slots(6 DIMMs per CPU)
•
Channel 0 is located furthest to processor, followed by channel 1 then
channel 2
•
DIMM 0 is the furthest from the processor of the two DIMMs in a given
channel
•
DIMM Capacity up to 16G
•
Speed is 800 MHz, 1067 MHz, 1333 MHz depending on DIMM
population
•
DIMM Voltage is 1.5V and LV 1.35V
•
Support all valid DIMM configurations as long as the total node power
is rated below the maximum value
Important Safety Information
Les "Viktig sikkerhetsinformasjon" på dokumentasjons-CDen før du installerer dette produktet.
Læs dokumentet Vigtige sikkerhedsoplysninger på dokumentations-cd'en, før produktet installeres.
Prima dell'installazione, leggere sul CD le Informazioni importanti sulla sicurezza.
Tärkeisiin turvatietoihin" Documentation CD -levyllä ennen tuotteen asentamista.
Läs dokumentet Viktig säkerhetsinformation på dokumentations-cd:n innan du installerar denna produkt.