HP RP7 HP Retail RP7 10.4" Customer Display Installation Instructions
HP RP7 Manual
 |
View all HP RP7 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP RP7 manual content summary:
- HP RP7 | HP Retail RP7 10.4" Customer Display Installation Instructions - Page 1
HP Retail RP7 10.4" Customer Display Installation Instructions Installing the Display 1. Slide down the two levers on the upper corners of the rear I/O panel 1 and rotate the cover off 2. 4. Connect the DVI, audio, USB, and power cables to the customer display. Insert the DVI cable into the - HP RP7 | HP Retail RP7 10.4" Customer Display Installation Instructions - Page 2
screen image. (This menu is only available when using VGA input.) OSD Control Adjusts the on-screen display (OSD) controls. Management Language Turns mode display and DDC/CI support on or off, and adjusts volume on models with integrated speakers. Selects the language in which the OSD menu is
-
1 -
2
 |
 |
HP Retail RP7 10.4”
Customer Display
Installation Instructions
© Copyright 2012 Hewlett-Packard Development Company, L.P. The
information contained herein is subject to change without notice.The only
warranties for HP products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should
be construed as constituting an additional warranty. HP shall not be liable
for technical or editorial errors or omissions contained herein.
Printed in
First Edition: May 2012
691057-001
Before Your Begin
Before installing the display, be sure to power off the system and
disconnect the power cord from the power outlet.
WARNING!
To avoid the risk of serious injury, ensure that the
power cord is unplugged from the electrical outlet at the wall
before installing the display. Failure to do so may expose you to
the risk of electric shock.
CAUTION:
To avoid the risk of damage to the system, ensure that
the power cord is unplugged from the electrical outlet at the wall
before installing the display.
1.
Slide down the two levers on the upper corners
of the rear I/O panel
1
and rotate the cover off
2
.
2.
Pull the power supply cover back then lift if up
and off the unit.
3.
Remove the decorative panel on the rear of the
unit by gently prying the panel away from the
base at the tab locations on the top and sides
of the panel as indicated below
1
. Then pull the
top of the panel away from the base
2
and
push straight down on the panel to release the
bottom tabs
3
.
4.
Connect the DVI, audio, USB, and power
cables to the customer display. Insert the DVI
cable into the retainer clip at the base of the
display head.
5.
Route the audio, DVI, USB, and power cables
through the hole in the customer display back
plate
1
. Connect the back plate to the customer
display by aligning the hooks on the back plate
with the slots on the back of the display and
sliding the back plate up
2
so that the screw
holes on the back plate are aligned with the
screw holes on the display. Install the two
screws to secure the back plate to the display
3
.
6.
Slide the cable ends through the hole in the
center of the decorative panel that was included
with the customer display.
7.
Route the audio, DVI, USB, and power cables
through the rear of the base and out the front of
the base, then up through the cable retainer on
the neck of the RP7 stand and connect the
cables to the RP7 I/O ports.
8.
Snap the decorative panel onto the rear of the
base.
9.
Slide the back plate mounting bracket into the
mounting hole on the rear of the RP7 base
1
,
and install the two screws included with the
customer display into the screw holes on top of
the mounting bracket
2
.
10.
Replace the power supply cover by lowering it
down over the neck of the base then sliding it
back until it snaps in place.
11.
Replace the rear I/O cover by placing the
hooks on the bottom of the cover into the slots
on the bottom of the chassis
1
. Then rotate the
top of the I/O cover up so that it snaps securely
onto the chassis
2
.
12.
Turn on power to the display.
Installing the Display