HP Scitex FB550 User Guide - Page 46

Printing gt; Options > Increase UV Lamp Power, Head Height off Media

Get HP Scitex FB550 PDF manuals and user guides View all HP Scitex FB550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

◦ When loading - Locates the left and right edges only when loading a roll of media. ◦ Before each copy - Locates the left and right edges of the media before each print. This enables the printer to compensate for any "drifting" of the media, and print the image at the correct location. ● Use Ionizer Bar - Sets whether to use the ionizer bar to reduce the electrostatic charge on synthetic medias (the default setting is on or enabled). You may want to disable the ionizer in humid environments where electrostatic charge is not present on the media, or to reduce the wear on the ionizer's discharge electrodes. The ionizer bar is powered on only during media load, printing, and when the lamps are on. ● Use Thickness Sensor - Sets whether to use the automatic media thickness sensor, or to prompt you to manually enter the thickness. ● Head Height off Media - Automatically raises the rail to set the printhead clearance from the media, at the height you specify. A lower height reduces overspray, but increases the chances for a head strike on the media. Bidi calibration is automatically adjusted for changes in this value. ● Print White Space - Provides the option of causing the printer to advance the media past unprinted space in the document file without the usual "printing" carriage motion. The printer will finish curing any printed areas before skipping this space. This option increases the printer's effective speed (throughput). ● Quality Check - When enabled, prevents printing from occurring if more than a certain number of missing or misfiring jets are not replaced by working jets. You can specify whether the printer asks you whether to stop printing with a Warning message, or if printing stops automatically without a Warning. ● Increase UV Lamp Power - When the printer is no longer fully curing the ink on prints, use this option to incrementally increase the lamp power. If the power needs to be increased again, create a custom media and set the UV Lamp Power to Medium or High, or replace the bulbs (the bulbs should be replaced in pairs). In this case, the printer will warn you that the print may not fully cure until the bulbs are replaced. (Printing Page > Options > Increase UV Lamp Power) ● Unidirectional Print Direction ● Use Fast Print Speed - Enables faster printing when using Indoor Signage Plus and Indoor Signage print modes. It is set to Yes by default, but you can turn it off by selecting No. ENWW Printing page 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
◦
When loading
—
Locates the left and right edges only when loading a roll of media.
◦
Before each copy
—
Locates the left and right edges of the media before each print. This enables
the printer to compensate for any “drifting” of the media, and print the image at the correct
location.
●
Use Ionizer Bar
—
Sets whether to use the ionizer bar to reduce the electrostatic charge on synthetic
medias (the default setting is on or enabled). You may want to disable the ionizer in humid
environments where electrostatic charge is not present on the media, or to reduce the wear on the
ionizer's discharge electrodes. The ionizer bar is powered on only during media load, printing, and when
the lamps are on.
●
Use Thickness Sensor
—
Sets whether to use the automatic media thickness sensor, or to prompt you
to manually enter the thickness.
●
Head Height off Media
—
Automatically raises the rail to set the printhead clearance from the media, at
the height you specify. A lower height reduces overspray, but increases the chances for a head strike on
the media. Bidi calibration is automatically adjusted for changes in this value.
●
Print White Space
—
Provides the option of causing the printer to advance the media past unprinted
space in the document file without the usual “printing” carriage motion. The printer will finish curing
any printed areas before skipping this space. This option increases the printer's effective speed
(throughput).
●
Quality Check
—
When enabled, prevents printing from occurring if more than a certain number of
missing or misfiring jets are not replaced by working jets. You can specify whether the printer asks you
whether to stop printing with a Warning message, or if printing stops automatically without a Warning.
●
Increase UV Lamp Power
—
When the printer is no longer fully curing the ink on prints, use this option
to incrementally increase the lamp power. If the power needs to be increased again, create a custom
media and set the UV Lamp Power to Medium or High, or replace the bulbs (the bulbs should be replaced
in pairs). In this case, the printer will warn you that the print may not fully cure until the bulbs are
replaced. (
Printing Page > Options > Increase UV Lamp Power
)
●
Unidirectional Print Direction
●
Use Fast Print Speed
—
Enables faster printing when using Indoor Signage Plus and Indoor Signage
print modes. It is set to
Yes
by default, but you can turn it off by selecting
No
.
ENWW
Printing page
39