HP Scitex LX850 HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui
HP Scitex LX850 Manual
View all HP Scitex LX850 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Scitex LX850 manual content summary:
- HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 1
SCITEX Dual Roll Kit User's guide - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 2
The only warranties for HP Products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 3
Table of contents 1 Introduction ...1 Purpose ...1 Main components ...1 Requirements ...1 2 Use of the dual-roll spindle 2 Load rolls onto the spindle ...2 Load rolls into the printer ...5 3 Troubleshooting ...10 4 Specifications ...11 ENWW iii - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 4
iv ENWW - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 5
HP Scitex LX800 Printer (126-in) ● HP Scitex LX820 Printer (126-in) ● HP Scitex LX850 Printer (126-in) ● HP Scitex LX600 Printer (104-in) ● HP Designjet L65500 Printer (104-in) For information about using these printers, refer to the corresponding User Guide or Maintenance and Troubleshooting Guide - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 6
spindle The dual-roll spindle is marked to assist you in positioning the differential hub. NOTE: The spindle marked A is for the dimensions of the 126-in spindle. The spindle marked B is for the dimensions of the 104-in spindle. Loading the dual-roll spindles 1. Ensure that the differential hubs on - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 7
the bolt. If you can still see the yellow spring, tighten the screw further. 3. At each end of the spindle, unscrew and remove the outer parts of the hub, using the Allen key. 4. Unscrew and remove the inner - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 8
Dual-roll spindle 5. Insert the first roll on the spindle. 6. Replace the hub, and secure it with the Allen key. 7. Insert the second roll on the spindle. 8. Replace the hub, and secure it with the Allen key. 9. Ensure that the end of the right-hand roll is located within the maximum allowed - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 9
the front dual-roll spindle. See Load rolls onto the spindle on page 2. 1. Tell the printer that you are going to begin loading for dual-roll printing. 2. Remove the substrate edge printheads and carriage. 3. Lift the substrate pressure handles at the rear of the printer. ENWW Load rolls into the - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 10
Dual-roll spindle 6. Bring the new rolls on their spindle to the rear of the printer, with the geared end of the spindle on the left. 7. If the two , the longer roll should be on the right as seen from the front of the printer; on the left as seen from the rear. NOTE: When the shorter roll comes - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 11
(if they were closed) and push the roll on its spindle into the printer. 10. Close the latches to secure the spindle in place. TIP: If that the printer has finished raising the carriage beam. 13. Pass the leading edges of both rolls through the printer to the output spindle. TIP: LX850/LX820 only: - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 12
Dual-roll spindle 14. Once in front of the printer, if you find that you haven't unrolled enough Substrate management, and press OK. Select Carriage beam position > Move to printing (normal) to lower the carriage beam into its normal position, close to the substrate. This process takes about 2 - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 13
may wrinkle in the print zone, to avoid ink smearing. Be aware that raising the printhead from by the printer in this way. In such cases, you will be asked to enter the required information manually. Use the -hand edge that must be entered manually. 21. In the HP Internal Print Server, choose from the - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 14
3 Troubleshooting If you see an error message numbered 78.2:01, it means that the substrate may have become layers of substrate stick to each other on the roll. If you experience ink smears on the substrate after a period of dual-roll printing, try removing the central edge holders. 10 - HP Scitex LX850 | HP Scitex LX850 & LX820 Printers: Dual Roll Kit User's Gui - Page 15
4 Specifications Printer length 126-in Printer Minimum roll width 914 mm (36 in) Maximum roll width 2 × 1.52 m (2 × 60 in) Minimum gap between 152 mm (6 in) rolls Maximum roll diameter 250 mm (9.84 in) Maximum total weight 2 × 60 kg (2 × 132 lb) of both rolls 104-in Printer 914 mm (36 in)
SCITEX Dual Roll Kit
User’s guide