HP Visualize b2000 hp Visualize b2000 UNIX workstation owner's guide (a5983-90 - Page 105

Installing the Floppy Disk Drive

Page 105 highlights

Changing Your Workstation's Hardware Configuration Removable Media Devices Figure 4-26 5. Remove the floppy disk drive from its shipping container. Using the four T-15 Torx/slotted blank filler screws, mount the disk drive to the bracket as shown in Figure 4-26. To help you properly install the floppy disk drive, you need to use the floppy disk drive holes labeled "A" on the bracket sides. The first T-15 Torx screws should be inserted through the tab holes of the floppy disk drive bracket that are located on the front part of both sides of the bracket. These T-15 Torx screws should then be screwed into the screw holes located on both sides of the floppy disk drive. These holes are located near the floppy disk drive's front panel. The remaining T-15 Torx screws should be insert through the holes labeled "A" at the back part of the floppy disk drive bracket. These screws should then be screwed into the rear screw holes located on both sides of the floppy disk drive. The front of the floppy disk drive should extend one inch from the front of the floppy disk drive bracket. See Figure 4-26. Installing the Floppy Disk Drive Floppy Disk Drive Front Panel Floppy Disk Drive Mounting Screws (T-15 Torx Screws) Floppy Disk Drive Bracket Bracket Screws 6. Slide the floppy disk drive and its bracket into the workstation Chapter 4 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229

Chapter 4
105
Changing Your Workstation’s Hardware Configuration
Removable Media Devices
5.
Remove the floppy disk drive from its shipping container. Using the
four T-15 Torx/slotted blank filler screws, mount the disk drive to the
bracket as shown in Figure 4-26.
To help you properly install the floppy disk drive, you need to use the
floppy disk drive holes labeled “A” on the bracket sides. The first T-15
Torx screws should be inserted through the tab holes of the floppy
disk drive bracket that are located on the front part of both sides of
the bracket. These T-15 Torx screws should then be screwed into the
screw holes located on both sides of the floppy disk drive. These holes
are located near the floppy disk drive’s front panel. The remaining
T-15 Torx screws should be insert through the holes labeled “A” at the
back part of the floppy disk drive bracket. These screws should then
be screwed into the rear screw holes located on both sides of the
floppy disk drive. The front of the floppy disk drive should extend one
inch from the front of the floppy disk drive bracket. See Figure 4-26.
Figure 4-26
Installing the Floppy Disk Drive
6.
Slide the floppy disk drive and its bracket into the workstation
Floppy Disk Drive Mounting
Screws (T-15 Torx Screws)
Bracket Screws
Floppy Disk
Drive Front
Panel
Floppy Disk Drive Bracket