Hitachi 50GX49B Owners Guide - Page 24

Pip Button, Single Mode Pip, Picture-in-picture Cont., Surf Mode Pip

Get Hitachi 50GX49B PDF manuals and user guides View all Hitachi 50GX49B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

PICTURE-IN-PICTURE (PIP) - 24 - ANT A input can be viewed as both the main picture and Sub-Picture simultaneously. ANT B and COMPONENT: Y-CBCR Input 2 sources can only be viewed as a main picture. To select between main picture and PIP Sub-Picture tuning, press PIP CH button on the remote. Every press of the PIP CH will highlight the main or sub-PIP source. The top channel display is the main picture and the bottom display is the sub-picture.This method of picture tuning is the same for one antenna input (ANT A only) and two antenna inputs (ANT A and ANT B). The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing other programs from the ANT A source or any of the video inputs. (1) PIP button Press the PIP button and a Sub-Picture appears in one of the two different modes (SINGLE or SURF), depending on the last selection of the PIP mode. To change the PIP mode use the CURSOR OR buttons and the new selection will appear the next time the PIP function is used. SINGLE MODE PIP Press the PIP button and a sub-picture appears in one corner of the screen. Press the button again to reduce the size of the sub-picture. Press teh PIP button a third time to remove the sub-picture from the screen. Use the PIP CH button to select between main and sub-picture tuning control (indicated by highlight). Press teh INPUT button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, and ANT A antenna source. (ANT B source cannot be viewed as a sub-picture and COMPONENT: Y-CB-CR Input 2 source will be displayed as a blank sub-picture). NOTE: Since ANT B source cannot be viewed as a sub-picture, only single PIP mode is possible when ANT B is selected as the main channel. When the COMPONENT: Y-CB-CR Input 2 is selected as PIP, it will appear as a blank sub-picture. PICTURE-IN-PICTURE CONT. SURF MODE PIP This feature will automatically scan all active channel numbers (those set in memory) and display them as PIP sub-pictures, along the right edge of the screen. Press the PIP button a second time to remove the sub-pictures from the screen. NOTE: 1. If no buttons are pressed when in SURF mode, auto-scanning will continuously scan.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
PICTURE-IN-PICTURE (PIP)
- 24 -
ANT A input can be viewed as both the main picture and
Sub-Picture simultaneously.
ANT B and COMPONENT: Y-CB-
CR Input 2 sources can only be viewed as a main picture. To select between main picture and PIP Sub-Picture
tuning,
press PIP CH button on the remote.
Every press of the PIP CH will highlight the main or sub-PIP source. The top channel
display is
the main picture and the bottom display is the sub-picture.This method of picture tuning is the same for one
antenna input (ANT A only) and two antenna inputs (ANT A and ANT B).
The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can
watch a TV program while viewing other programs from the ANT A source or any of the video inputs.
(1) PIP button
Press the PIP button and a Sub-Picture appears in one of the two different modes (SINGLE or SURF), depending on the last
selection of the PIP mode. To change the PIP mode use the CURSOR
OR
buttons and the new selection will
appear the next time the PIP function is used.
SINGLE MODE PIP
Press the PIP button and a sub-picture appears in one corner of the screen. Press the button again to reduce the size of the
sub-picture. Press teh PIP button a third time to remove the sub-picture from the screen. Use the PIP CH button to select
between main and sub-picture tuning control (indicated by highlight). Press teh INPUT button when sub-picture channel
tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, and ANT A antenna source. (ANT B source cannot be
viewed as a sub-picture and COMPONENT: Y-CB-CR Input 2 source will be displayed as a blank sub-picture).
NOTE:
Since ANT B source cannot be viewed as a sub-picture, only single PIP mode is possible when ANT B is selected
as the main channel.
When the COMPONENT: Y-CB-CR Input 2 is selected as PIP, it will appear as a blank sub-picture.
PICTURE-IN-PICTURE CONT.
SURF MODE PIP
This feature will automatically scan all active channel numbers (those set in memory) and display them as PIP sub-pictures,
along the right edge of the screen. Press the PIP button a second time to remove the sub-pictures from the screen.
NOTE:
1. If no buttons are pressed when in SURF mode, auto-scanning will continuously scan.