Hitachi 61UDX10B Owners Guide - Page 31

USING THE REMOTE TO CONTROL ADDITIONAL AUDIO/VIDEO EQUIPMENT Operating the precoded function for your Audio/Video component. This remote is designed to operate different types of Audio/Video component. You must first program the remote to match the remote system of your Audio/Video component. (refer to page 32 for pre-codes) 1. Turn ON your Audio/Video component you wish to control with the Remote. 2. Aim the remote control at the front of your Audio/Video component. 3. Press and release the AV1, AV2 or AV3 button to switch to Audio/Video component pre-coded mode. 4. Hold down the AV1, AV2 or AV3 button on the remote and enter the two digit preset code that matches your Audio/Video component, as shown on page 32. The indicator light will flash 3 times if the code was accepted. 5. Aim the remote at the Audio/Video component and press the POWER button. The remote will turn off your Audio/Video component when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your Audio/Video component. If the Audio/Video component does not turn off, try a different two digit preset code. 6. The remote will now control your Audio/Video component. 7. Repeat steps 1 - 6 if you wish to program the remote to control another Audio/Video component. Be sure to use a different A/V button on the remote, since only one component can be programmed per button. NOTES: 1. Your remote control SOURCE WIZARD buttons are either labeled as AV1, AV2 and AV3, or CD, TAPE, and AMP. If your remote control SOURCE WIZARD buttons are labeled as AV1, AV2, and AV3, please program your Audio/Video components as follow for best performance. Use AV1 to program your CD brand. Use AV2 to program your TAPE brand, and use AV3 to program your AMPLIFIER/RECEIVER brand. 2. If your Audio/Video component cannot be operated after performing the above procedures, your Audio/Video component s code has not been precoded into the remote. 3. In the unlikely event that your Audio/Video component cannot be operated after performing the above procedures, please consult your Audio/Video equipment operating guide. 4. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. ቢ AV1, AV2, AV3 Buttons These buttons allows the remote to control your Audio/Video equipment by setting it to Audio/Video mode. ባ PRECODED AUDIO/VIDEO Buttons These buttons transmit the chosen precoded Audio/Video component codes. ቤ EXCLUSIVE TV Buttons These buttons are for operating the TV. ባ POWER TV DVD VCR CBL SOURCE WIZARD AV1 AV2 STB AV3 1 2 3 ቢ 4 5 6 7 8 9 ቤ SLEEP ANT C.C. 0 LAST CH HELP ASPECT PIX ባ POWER TV DVD VCR CBL SOURCE WIZARD CD TAPE STB AMP 1 2 3 ቢ 4 5 6 7 8 9 ቤ SLEEP ANT C.C. 0 LAST CH HELP ASPECT MODE ቤ MENU EXIT VOL SELECT CH ቤ MENU EXIT VOL SELECT CH ባ SVCS VID 1 MUTE STATUS VCR PLUS+ INFO GUIDE/TV SCHD VID 5 VID 2 VID 4 VID 3 PIP PIP CH FREEZE PIP MODE PIP ACCESS SWAP PROG TV/VCR SLOW REC ቤ ባ SVCS VID 1 MUTE STATUS VCR PLUS+ INFO GUIDE/TV SCHD VID 5 VID 2 VID 4 VID 3 PIP PIP CH FREEZE PIP MODE PIP ACCESS SWAP PROG TV/VCR SLOW REC ቤ CLU-5711TSI CLU-5713TSI MY AUDIO/VIDEO EQUIPMENT CODE IS: AV1 (CD) AV2 (TAPE) AV3 (AMP/RCVR) NOTE: Refer to instruction manual of the Audio/Video equipment for operation of the buttons exclusively for the Audio/Video equipment. 31