Hitachi DH24PC3 Instruction Manual - Page 15

Hammering only, Using depth gauge Fig. 15, How to use the drill bit taper shank, and the taper shank

Get Hitachi DH24PC3 - 15/16inch SDS Plus Rotary Hammer 3 Mode PDF manuals and user guides
UPC - 717709009981
View all Hitachi DH24PC3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

English 6. Hammering only This rotary hammer can be set to hammering only mode by pressing the push button and turning the change lever to mark. (Fig. 12) (1) Mount the bull point or cold chisel. (2) Press the push button and set the change lever to middle of mark and mark. (Fig. 13) The rotation is released, turn the grip and adjust the cold chisel to desired position. (Fig. 14) (3) Turn the change lever to mark. (Fig. 12) Then bull point or cold chisel is locked. 7. Using depth gauge (Fig. 15) (1) Loosen the knob on the side handle, and insert the depth gauge into the mounting hole on the side handle. (2) Adjust the depth gauge position according to the depth of the hole and tighten the knob bolt securely. 8. How to use the drill bit (taper shank) and the taper shank adaptor. (1) Mount the taper shank adaptor to the rotary hammer. (Fig. 16) (2) Mount the drill bit (taper shank) to the taper shank adaptor. (Fig. 16) (3) Turn the switch ON, and drill a hole in prescribed depth. Mounting hole Depth gauge Change lever Push button Fig. 12 Change lever Push button Fig. 13 Grip Fig. 14 Drill bit Grip Knob on side handle Fig. 15 Taper shank adaptor Front cap Fig. 16 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
15
English
6.
Hammering only
This rotary hammer can be set to
hammering only mode by pressing the
push button and turning the change
lever to
mark. (Fig. 12)
(1) Mount the bull point or cold chisel.
(2) Press the push button and set the
change lever to middle of
mark and
mark. (Fig. 13)
The rotation is released, turn the grip
and adjust the cold chisel to desired
position. (Fig. 14)
(3) Turn the change lever to
mark.
(Fig. 12)
Then bull point or cold chisel is locked.
7.
Using depth gauge (Fig. 15)
(1) Loosen the knob on the side handle,
and insert the depth gauge into the
mounting hole on the side handle.
(2) Adjust the depth gauge position ac-
cording to the depth of the hole and
tighten the knob bolt securely.
8.
How to use the drill bit (taper shank)
and the taper shank adaptor.
(1) Mount the taper shank adaptor to the
rotary hammer. (Fig. 16)
(2) Mount the drill bit (taper shank) to the
taper shank adaptor. (Fig. 16)
(3) Turn the switch ON, and drill a hole in
prescribed depth.
Fig. 16
Drill bit
Taper shank
adaptor
Front cap
Grip
Mounting hole
Depth gauge
Knob on side
handle
Fig. 15
Change lever
Push
button
Change lever
Push
button
Fig. 12
Fig. 13
Fig. 14
Grip