Honeywell 5804 Installation Guide

N7674-6V2

10/04

Rev. A

ADEMCO 5804E

ADEMCO 5804E

ADEMCO 5804E

ADEMCO 5804E

WIRELESS KEY TRANSMITTER




INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The ADEMCO 5804E is a compact, 4-button

portable wireless transmitter intended for use only

with wireless alarm systems that support 5800

Series receivers.

Each button on the transmitter

may be programmed for any zone response, but is

typically used for arming and disarming.

This device supports the High-Security mode,

which sends rolling-code encrypted messaging to

the RF receiver.

Important Note: This device must be used with

a 5881EN or a 6128RF (UL version) receiver.

The 5804E is powered by two replaceable lithium

batteries designed to provide up to 4 years of life.

For

battery

installation,

see

Replacing

the

Batteries

.

PROGRAMMING

Each 5804E is assigned a unique serial number

during manufacture.

Each button on the unit also

has a distinct "loop" number (refer to Figure 1) that

you must program into the control panel during

installation.

Assign each button to an individual

zone and designate the Input Type as "BR"

(Button Type RF).

When you are prompted for the serial number,

either press and release twice the button you are

programming, or enter it manually through the

keypad.

For complete details on how to program the 5804E

transmitter's serial number at the control panel,

see the control unit's installation instructions.

Note:

Buttons on this transmitter must be pressed

for at least 1/2 second to activate the transmitter.

This feature minimizes the possibility of accidental

transmissions.

ACTIVATING HIGH-SECURITY MODE

If Programming 5804E in the Control

1.

Program the button in the control.

2.

After programming is complete, exit

programming mode and wait 60 seconds.

3.

Put the system in Go/No Go mode.

4.

Press all 4 buttons on the 5804E at the same

time until the panel beeps.

5.

To sync the device in High Security Mode,

press any button ONCE, until the panel beeps

indicating receipt.

NOTE:

If no beep is heard, exit Go/No Go

mode, and repeat this procedure from Step 3.

6.

Exit Go/No Go mode (user code + 1 (OFF)).

LOOP 4

LOOP 1

LOOP 2

ON

OFF

5804E-001-V0

LOOP 3

Figure 1:

5804E showing button designations

PROGRAMMING THE 5804E LOCALLY IN

AN RF KEYPAD (E.G., 6150RF)

Hold all 4 buttons down while enrolling the serial

number in the RF keypad.

USING

TWO

RECEIVERS

IN

HIGH-

SECURITY MODE

Enroll the 5804E into the receivers one at a time,

by

disconnecting

Receiver

#2,

enrolling

as

described in “Activating High Security Mode”

(above).

Then, disconnect Receiver #1, reconnect

Receiver #2, and repeat the enrollment procedure.

This

process

ensures

proper

High

Security

operation with both receivers.

APPLYING COLORED ADHESIVE LABELS

AND BUTTONS

The 5804E is supplied with colored buttons (red

and blue) and colored adhesive identification

labels (blue, red, gray, and green).

Each label has

a specified command function and symbol printed

on it, as well as an adhesive back for easy pasting.

To paste a label on a button,

slowly peel off a

label with a selected function and paste it on the

button of the transmitter.

If you decide later to re-

enroll a button, the label can be easily removed or

a new label pasted over the existing one.

Additional colored buttons (red and blue) are also

provided which can be used with or without the

labels.

The buttons can be inserted only in the

areas provided for them (see Figure 3).

Honeywell 5804 Installation Guide

Honeywell 5804 - Ademco Wireless Key Manual

Honeywell 5804 manual content summary: