Honeywell 5828V Installation Guide - Page 1
Honeywell 5828V - Ademco Wireless Talking Keypad Manual
UPC - 781410492837
View all Honeywell 5828V manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
K0020V2 6/06 Rev. B ADEMCO 5828/5828V Wireless Bidirectional Fixed-Word Keypads INSTALLATION AND SETUP GUIDE GENERAL INFORMATION The ADEMCO 5828 and 5828V are wireless, bidirectional, fixed-word, keypads that may be used in conjunction with LYNX and VISTA series residential control panels. VISTA systems require use of either a 5883 Transceiver (micro P/N WAK5119-X, where X = 3 or higher), 6150RF Keypad/ Transceiver (PC board P/N SA6150RFAS-T3 or higher), or 6160RF Keypad/Transceiver. The 5828/5828V keypads are not compatible with commercial control panels that have three-digit zone numbers (e.g., VISTA128BP). Both keypads provide: • Four programmable special function keys • Wall-mount plate for easy removal of the keypad and battery replacement • Optional Desktop mount /AC adapter kit, ADEMCO P/N 5828DM) • Battery-powered with 3-AA batteries The 5828V keypad additionally provides: • Memo/Message center • Voice Response - system status, zone information, and alarms with zone information • Stored Message LED indication • Built-in microphone and speaker NOTES: • The 5828/5828V cannot be used as the primary system keypad, and may not be used to program or test any security system. All systems require a hardwired keypad (or Compass Downloader) to do so. Once programmed, the 5828/5828V can be used to initiate all common functions of a fixed English keypad. A B ARMED READY C 1 OFF 4 MAX 7 INSTANT READY 2 AWAY 5 TEST 8 CODE 0 3 STAY 6 BYPASS 9 CHIME # D 5828 Keypad with Front Cover Removed 5828-00-001-V0 Operation (See NOTE below) 1. Battery-Powered Operation: When powered by battery, the keypad activates when any key is pressed. When the [✱] key is pressed, the keypad sends a system status request, and displays and/or annunciates the present status transmitted by the system. 2. AC-Powered Operation: When powered by AC, the keypad remains active at all times. Any change in system status will cause the display to automatically turn on (if blank) and display/annunciate the new status. If AC power is lost, the keypad will revert to battery-powered operation until AC power is restored and a new status request is made ([✱] key). NOTE: Whether the unit is powered by battery or AC, the 5828/5828V may take up to 5 seconds to display and/or annunciate the new status after pressing the [✱] key. WALL MOUNTING Before mounting the 5828 & 5828V permanently, determine a good RF location as follows: • If interfacing to a LYNX panel, try communicating with the panel from different locations. • If interfacing to a VISTA panel, perform a Go/No Go test from the panel. Refer to the Go/No Go test mode in the Installation and Setup Guide for the panel. Avoid mounting locations on or near large metal objects, since these can decrease the transmission range or block transmissions. • Secure the mounting plate to the wall, using proper sized hardware through the six mounting holes. • Plug the cord from the optional power pack into the keypad's DC input connector, and route the wires through the wire guides on the back of the keypad. • Position the keypad over the mounting plate and slide down, engaging the four retaining clips on the plate with the receptacles on the keypad. DESKTOP MOUNTING For full portability, the keypad may be placed in any convenient, RF-suitable location and operated in its batterypowered mode, or near an AC outlet to be powered by the optional Power Pack/Desktop Mounting Kit, ADEMCO P/N 5828DM. MIC MESSAGE A B ARMED READY C D 1 OFF RECORD 4 MAX 2 AWAY VOLUME 5 TEST 3 STAY PLAY 6 BYPASS 7 INSTANT 8 CODE 9 CHIME READY STATUS 0 # VOICE FUNCTION 5828V-00-002-V0 5828V Keypad with Front Cover Removed BATTERY INSTALLATION OR REPLACEMENT CAUTION: Remove the AC/DC power connector from the keypad (if applicable), before attempting to install or replace the batteries. 1. Separate the keypad from its mounting plate by sliding the keypad up and away from the mounting plate. 2. Open the battery compartment door to expose the batteries.