Honeywell 5828V Installation Guide - Page 2
Programming or Changing a User Code Required if - wireless keypad
UPC - 781410492837
View all Honeywell 5828V manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
3. Install or replace the 3-1.5 Volt AA batteries in the battery compartment. Always replace all three batteries at once to ensure normal operation of the keypad over the anticipated battery lifetime. Make sure that battery positive (+) and negative (-) terminals are properly oriented with the battery spring clip connections. Refer to battery placement graphic below. AA BATTERY AA BATTERY AA BATTERY batt_case-001-V0 Battery Compartment 4. Reattach the keypad to its mounting plate by aligning the four mounting holes in the keypad case back with the four mounting clips on the mounting plate. Lower the keypad onto the clips. PROGRAMMING The following two items must be programmed in the keypad by the installer. • House ID Code (Step 1 in Installer Programming mode)* • System Type (Step 2 in Installer Programming mode) *The same House ID Code must also be programmed in the control panel. Programming a different House ID will disable communication. Installer Programming Enter the program mode by pressing the [1] and [3] keys simultaneously for five (5) seconds. The display alternately flashes "00" and two dashes (--). NOTES: • Entering a value other than one specified in the following steps may cause unpredictable results. • This keypad exits programming mode 15 seconds after the last key is pressed. Pressing any key will extend the 15-second active time. If the unit times out before you have pressed the star (✱) key to save a programmed value, you will need to re-enter the Programming mode and reprogram the option. STEP 1. 2. ACTION Press [1] (House ID Code) (10 = default) Enter the two-digit house code (01-31) Press [✱] to continue. Press [2] (System Type). Press (1) for VISTA Press (2) for LYNX (2 = default) Press [✱] to continue. DISPLAY Alternately flashes "t1" and the 2digit house code. Alternately flashes "t2" and (1 or 2) 3. 4. (5828V only) 5. 6. 7. Press [3] (Exit Delay) Press 0-9 in 15 second increments. Example: If you press 3, exit delay would be 3 times 15 seconds for a total of 45 seconds. NOTE: The Exit Delay programmed here should match the Exit Delay programmed in the control panel. (0 = default) Press [✱] to continue. Press [4] (Voice enable/disable). Press (0) to disable. Press (1) to enable. (1 = default) Press [✱] to continue. Press [5] (Wireless Protocol). Press [1] for original LYNX controls Press [2] for LYNXR, LYNXR-EN, or VISTA controls (2 = default) Press [✱] to continue. Press [6] (Function Key Select). Press [0] for Panic Key Press [1] for Single-button arming NOTE: The programming here must match the programming of the control panel to simplify end user operation. (1 = default.) Press [✱] to continue. Press [7] (Restore Defaults). Press [1] to restore factory settings. Press [✱]. Exit programming mode. Alternately flashes "t3" and value selected. Alternately flashes "t4" and (0 or 1) Alternately flashes "t5" and (1 or 2) Alternately flashes "t6" and (0 or 1) Displays "EE" Exiting Programming Mode You can exit programming mode by pressing the [✱] key whenever the small 00 and (- -) are alternately displayed. Programming or Changing a User Code (Required if using Quick Arm function on LYNX or VISTA) Enter user program mode by pressing the [7] and [9] keys at the same time until the display flashes double dashes (- -). Enter the desired 4-digit user code that matches a user code programmed in the control panel. There will be no display of the user code entered. Press the [✱] key to place the 4-digit code in memory and exit the user program mode. SPECIAL FUNCTION KEYS As shown in the figures on page 1, each keypad contains four Special Function keys (A, B, C, D) that may be programmed to execute the commands shown below. NOTE: The Function Key Select setting in Step 6 of the INSTALLER PROGRAMMING procedure above determines the operation of the Special Function keys A, B, C, and D as follows: If you select "0" Function Key A B C D Function Message Sent to Control [1] + [✱] (Alarm zone 95) [✱] + [#] (Alarm zone 99) [3] + [#] (Alarm zone 96) (Not used for panic alarms) NOTE: Do NOT use the 5828V for silent panic operation because the keypad itself is not silent. - 2 -