Honeywell 6460S Installation Guide
Honeywell 6460S Manual
 |
View all Honeywell 6460S manuals
Add to My Manuals
Save this manual to your list of manuals |
Honeywell 6460S manual content summary:
- Honeywell 6460S | Installation Guide - Page 1
AND SETUP GUIDE GENERAL INFORMATION The ADEMCO 6460S (silver) and 6460W (white) are addressable Remote Keypads designed for use with Honeywell's ADEMCO series control panels. Addresses are set via the keypad keys. The keys on the keypad are continuously backlit for convenience. NOTE: If supported - Honeywell 6460S | Installation Guide - Page 2
instructions). OPERATING THE KEYPAD For operating instructions, see the User Guide for the control panel used with this keypad. SPECIFICATIONS Physical: 5-9/16"H x 6-3/4"W x 1"D Displays: 2 x 16 alpha-numeric supertwist LCD 2009 Honeywell International Inc. www.security.honeywell.com 800
-
1 -
2
 |
 |
800-03612
1/09
Rev. B
ADEMCO
ADEMCO
ADEMCO
ADEMCO 6460S
6460S
6460S
6460S/6460W
/6460W
/6460W
/6460W
REMOTE KEYPAD
REMOTE KEYPAD
REMOTE KEYPAD
REMOTE KEYPAD
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
The ADEMCO 6460S (silver) and 6460W (white) are
addressable Remote Keypads designed for use with
Honeywell's ADEMCO series control panels. Addresses are
set via the keypad keys.
The keys on the keypad are continuously backlit for
convenience.
NOTE:
If supported, the ADEMCO 6460S and 6460W
keypads are supervised by control panel. Supervision must
be enabled for commercial fire installations.
KEYPAD DISPLAYS AND LEDS
The ADEMCO 6460S and 6460W keypads have the
following display features:
•
2-line Alpha Display
•
Custom Zone Descriptors
•
Built-in Speaker Sounder
•
Dedicated Function Keys
•
Backlit Display (permanent display backlighting is
an option on some controls; see the control's
instructions for details).
The following table shows the LEDs and their functions:
LED
Function
Red
Lights when the system is armed in any mode
Green
Lights when the system is "ready" to be armed.
SPECIAL FUNCTION KEYS
The keypads also feature function keys.
These keys may be
programmed for panic alarms or other special functions
such as macros. See the control's instructions for details.
Function keys must be held down for at least 2
seconds to activate an alarm; key pairs are activated
immediately.
Function Keys
A or [1] and [
✻
]
B or [
✻
] and [#]
C or [3] and [#]
D
WIRING AND INSTALLATION
The keypads can be surface mounted directly to a drywall,
or to a single- or double-gang electrical box.
1.
Push the two case release snaps at the bottom of the
keypad with the blade of a medium screwdriver (this will
push in the release snap), then pull that side of the case
back away. Refer to Figure 1 for location of the case back
release snaps.
2. Route wiring from the control panel through the opening
in the case back.
3. Mount the case back to a wall or electrical box.
4. Wire directly from the keypad’s terminal block
to the
terminal block on the control panel. (See Wiring Table
below).
NOTE:
No more than one wire per terminal may be
connected. If daisy-chained configuration is required,
pig-tail wires together so that only one wire is
terminated under the screw. Use 16-24
AWG wire only!
Wiring Table
Keypad
Control Panel
Wire Color
▲
G
Data In
Green
–
– Aux Pwr (GND)
Black
+
+ Aux. Pwr
Red
▼
Y
Data Out
Yellow
See the control panel’s Installation and Setup Guide for
more complete details.
5. Reattach the keypad
to its case back.
JKL
AWAY
CODE
ARMED
READY
STAY
OFF
MAX
D
INS
EN
I
GH
RS
PQ
T
TAN
READY
BYPASS
CHIME
TEST
4
6
TUV
9
0
NO
M
XZ
Y
W
UM
N
EF
D
ABC
3
5
8
2
1
7
*
#
NOTE:
TO REMOVE CASE BACK
PUSH IN THE TWO RELEASE
SNAPS LOCATED ALONG THE
BOTTOM OF THE KEYPAD
AND LIFT UP.
6460S-001-V1
RELEASE
SNAPS
D
C
B
A
Figure 1. Removing the Case Back
WWW.DIYALARMFORUM.COM
WWW.DIYALARMFORUM.COM