Husqvarna HU775BBC Owners Manual - Page 13

To Change Engine Oil See Fig. 16, Air Filter See Fig. 17, Muffler, Spark Plug, In-line Fuel Filter

Page 13 highlights

MAINTENANCE Change the oil after every 25 hours of operation or at least once a year if the lawn mower is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil plug securely each time you check the oil level. TO CHANGE ENGINE OIL (See Fig. 16) NOTE: Before tipping lawn mower to drain oil, empty fuel tank by running engine until fuel tank is empty. 1. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 2. Remove engine oil cap; lay aside on a clean surface. 3. Tip lawn mower on its side as shown and drain oil into a suitable container. Rock lawn mower back and forth to remove any oil trapped inside of engine. CAUTION: Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge. 4. Install cartridge, then replace cover making sure the tabs are aligned with the slots in the back plate. Fasten screw securely. LIP BACK PLATE CARTRIDGE SLOT COVER COVER TAB CONTAINER FIG. 16 4. Wipe off any spilled oil from lawn mower or side of engine. 5. Slowly pour oil down the oil fill spout, stopping every few ounces to check the oil level with the dipstick. 6. Stop adding oil when you reach the FULL mark on the dipstick. Wait a minute to allow oil to settle. 7. Continue adding small amounts of oil, rechecking the dipstick until oil level settles at FULL. DO NOT overfill, or engine will smoke heavily from the muffler on startup. 8. Always be sure to retighten oil dipstick before starting engine. 9. Reconnect spark plug wire to spark plug. AIR FILTER (See Fig. 17) Your engine will not run properly and may be damaged by using a dirty air filter. Replace the air filter cartridge every 100 hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions. TO CLEAN AIR FILTER 1. Loosen screw and tilt cover to remove. 2. Carefully remove cartridge. 3. Clean by gently tapping on a flat surface. If very dirty, replace cartridge. MUFFLER FIG. 17 Inspect and replace corroded muffler as it could create a fire hazard and/or damage. SPARK PLUG Replace spark plug at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the "PRODUCT SPECIFICATIONS" section of this manual. IN-LINE FUEL FILTER (See Fig. 18) The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. 1. With engine cool, remove filter and plug fuel line sections. 2. Place new fuel filter in position in fuel line with arrow pointing towards carburetor. 3. Be sure there are no fuel line leaks and clamps are properly positioned. 4. Immediately wipe up any spilled gasoline. CLAMP CLAMP FUEL FILTER 13 FIG. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

13
FIG. 17
BACK PLATE
SLOT
LIP
COVER
TAB
CARTRIDGE
COVER
CAUTION:
Petroleum solvents, such as
kerosene, are not to be used to clean
cartridge. They may cause deterioration
of the cartridge. Do not oil cartridge.
Do not use pressurized air to clean or
dry cartridge.
4.
Install cartridge, then replace cover making sure the
tabs are aligned with the slots in the back plate. Fasten
screw securely.
MAINTENANCE
Change the oil after every 25 hours of operation or at least
once a year if the lawn mower is not used for 25 hours in
one year.
Check the crankcase oil level before starting the engine
and after each five (5) hours of continuous use. Tighten oil
plug securely each time you check the oil level.
TO CHANGE ENGINE OIL (See Fig. 16)
NOTE
:
Before tipping lawn mower to drain oil, empty fuel
tank by running engine until fuel tank is empty.
1.
Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
2.
Remove engine oil cap; lay aside on a clean surface.
3.
Tip lawn mower on its side as shown and drain oil into
a suitable container. Rock lawn mower back and forth
to remove any oil trapped inside of engine.
CONTAINER
FIG. 16
4.
Wipe off any spilled oil from lawn mower or side of
engine.
5.
Slowly pour oil down the oil fill spout, stopping every
few ounces to check the oil level with the dipstick.
6.
Stop adding oil when you reach the FULL mark on the
dipstick.
Wait a minute to allow oil to settle.
7.
Continue adding small amounts of oil, rechecking the
dipstick until oil level settles at FULL.
DO NOT over-
fill, or engine will smoke heavily from the muffler on
startup.
8.
Always be sure to retighten oil dipstick before starting
engine.
9.
Reconnect spark plug wire to spark plug.
AIR FILTER (See Fig. 17)
Your engine will not run properly and may be damaged
by using a dirty air filter. Replace the air filter cartridge
every 100 hours of operation or every season, whichever
occurs first.
Service air cleaner more often under dusty
conditions.
TO CLEAN AIR FILTER
1.
Loosen screw and tilt cover to remove.
2. Carefully remove cartridge.
3.
Clean by gently tapping on a flat surface. If very dirty,
replace cartridge.
MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
SPARK PLUG
Replace spark plug at the beginning of each mowing season
or after every 100 hours of operation, whichever occurs
first.
Spark plug type and gap setting are shown in the
“PRODUCT SPECIFICATIONS” section of this manual.
IN-LINE FUEL FILTER (See Fig. 18)
The fuel filter should be replaced once each season.
If fuel
filter becomes clogged, obstructing fuel flow to carburetor,
replacement is required.
1.
With engine cool, remove filter and plug fuel line sections.
2.
Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
3.
Be sure there are no fuel line leaks and clamps are
properly positioned.
4.
Immediately wipe up any spilled gasoline.
FIG. 18
FUEL
FILTER
CLAMP
CLAMP