Husqvarna LE475 Owners Manual - Page 11

LAWN EDGER AND TRIMMER PARTS LIST REF. PART NO. NO. DESCRIPTION 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16 16A 17 18 19 20 21 22 23 24 25 26 27 28 29 31 33 505289901 Handle 505289902 Pin, Cotter 1/8 x 3/4 (2 Req.) 505289903 Nut Lock Hex 7/16" - 14 (4 Req.) 505289904 Spring 505289905 Bolt, Hex 7/16 - 14 x 2 505289906 Rod, Clutch & Depth 505289907 Grip (3 Req.) 505289908 Lever, Clutch & Depth 505289909 Throttle Control (3 HP Ball Brg) (40-3/4) 505289910 Clip, Throttle Cable 505289911 Cross Brace for Handle 505289912 Nut 1/4-28 Hex (10 Req.) 505289913 Bolt 1/4-28 x 7/8 hex (6 Req.) 505289914 Frame, Right Hand 8" 505289915 Hub Cap for 7" & 8" Rear Wheels 505289916 8" Rear Wheel Complete w/ Bearings, Wide Tire & Hub Cap 505289917 8" Rear Wheel Outside Bearing Only 505289918 8" Rear Wheel Inside Bearing Only. Also for 8" Front Wheel. (2 needed/front) 505289919 8" Front Wheel Complete w/Bearing & Wide Tire 505289920 8" Tire Only 505289921 8" Rear Wheel Rim Only 505289922 --- -- -- -505289924 505289925 505289926 8" Front Wheel Rim Only Engine (Briggs & Stratton Dist.) Bolt 5/16-24 x 1-1/2 (4 Req.) Bolt 5/16-24 x 7/8 Hex (5 Req.) Nut 7/16-14 Hex (3 Req.) 505289927 8" Front Axle 505289928 8" Front Wheel Spacer (2-13/16" Use With 7075-7 Wheels) 505289929 Nut 5/16-24 Hex (9 Req.) 505289930 8" Fram Crossmember 505289931 8" Rear Axle (13-5/8") (Use with 7058 wheels) 505289932 Bracket, Engine Pulley Guard 505289933 Guard, Engine Pulley 505289934 Engine Pulley Guard & Bracket Complete 505289935 Screw #10 x x1/2 Sheet Metal (4 Req.) 505289936 8" Fram, Left Hand 505289937 Set Screw 5/16-24 x 5/16 505289938 Cutterhead Pulley & Shaft Comp. 30 505289937 Engine Pulley REF. PART NO. NO. 34 35 36 36A 37 40 41 42 44 45 46 47 49 50 51 52 53 54 55 56 57 58 59 61 62 63 505289939 505289940 505289941 505289943 505289942 505289944 505289945 505289946 505289947 505289948 505289949 505289950 505289951 505289952 505289953 505289954 505289955 505289956 505289957 505289958 505289959 505289960 505289961 505289962 505289963 505289964 505289965 505289966 505289967 505289968 505289969 DESCRIPTION Screw 1/4-20 x 1/2 Hex Cutterhead Pulley Guard Cutterhead Bearing (2 Req.) Spring Washer (New 01/87) Mandrel, Head Clamp, Blade Guard Bolt 1/4-28 x 1-1/2 Hex (2 Req.) Blade Guard Main Complete Blade Guard Washer, Friction (2 Req.) Nut 1/2-20 , Debris Sweep U-Clamp Complete Debris Guard Pivot Bolt Flat Washer 7/16 Spring, Head Recoil Cup Body, Cutterhead Lever, Angle Shifting Pin 5/16 x 2 Spring Brace Cutterhead Drive Belt (4L-300) Cutting Blade 1-1/4 Pin U-Clamp Spacer Grease Fitting Handle and Wheel Bearing Cutting Head Complete (Inc. No 33,53,51,52,54,55,56,61,37,(2)63, (2)36) LE475 Decal NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 11