Husqvarna RZ5424 Kohler Owners Manual - Page 52

Cables, Front Wheel Mount, Front Wheel Bearings, Deck Spindle, IMPORTANT INFORMATION

Get Husqvarna RZ5424 Kohler PDF manuals and user guides View all Husqvarna RZ5424 Kohler manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

LUBRICATION Cables If possible, grease both ends of the cables and move the controls to end stop positions when lubricating. Refit the rubber covers on the cables after lubrication. Cables with sheaths will bind if they are not lubricated regularly. If a cable binds, it can disrupt operation. If a cable binds, remove the cable and hang it vertically. Lubricate it with light engine oil until the oil begins to escape from the bottom. Tip: Fill a small plastic bag with oil and tape it so that it seals against the sheath and allow the cable to hang vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced. Front Wheel Mount Lubricate with a grease gun, one zerk for each wheel mount, until the grease is forced out. Use only good quality bearing grease. Grease from well-known brand names (petrochemical companies) usually maintains a good quality. Front Wheel Bearings Lubricate with a grease gun, one zerk for each set of wheel bearings, until the grease is forced out. Use only good quality bearing grease. IMPORTANT INFORMATION Use minimal lubrication and remove excess lubricant so that is does not come into contact with belts or belt pulley drive surfaces. Lubricating the front wheels Deck Spindle Lower the cutting deck completely. If a grease gun without a rubber hose is used, the foot plate must be removed. Lubricate with a grease gun, one zerk, 2-3 strokes. Use only good quality bearing grease. 8011-731 52-Husqvarna Deck spindle 8011-732

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
LUBRICATION
52
-Husqvarna
Cables
If possible, grease both ends of the cables and move
the controls to end stop positions when lubricating.
Refit the rubber covers on the cables after lubrication.
Cables with sheaths will bind if they are not lubricated
regularly. If a cable binds, it can disrupt operation.
If a cable binds, remove the cable and hang it
vertically. Lubricate it with light engine oil until the oil
begins to escape from the bottom.
Tip: Fill a small plastic bag with oil and tape it so that
it seals against the sheath and allow the cable to hang
vertically from the bag overnight. If you do not succeed
in lubricating the cable, it must be replaced.
Front Wheel Mount
Lubricate with a grease gun, one zerk for each wheel
mount, until the grease is forced out.
Use only good quality bearing grease.
Grease from well-known brand names (petrochemical
companies) usually maintains a good quality.
Front Wheel Bearings
Lubricate with a grease gun, one zerk for each set of
wheel bearings, until the grease is forced out.
Use only good quality bearing grease.
8011-731
Lubricating the front wheels
8011-732
Deck spindle
IMPORTANT INFORMATION
Use minimal lubrication and remove
excess lubricant so that is does not come
into contact with belts or belt pulley drive
surfaces.
Deck Spindle
Lower the cutting deck completely.
If a grease gun without a rubber hose is used, the foot
plate must be removed.
Lubricate with a grease gun, one zerk, 2-3 strokes.
Use only good quality bearing grease.