Husqvarna TS 148X Owner Manual - Page 25

Transmission, Engine

Get Husqvarna TS 148X PDF manuals and user guides View all Husqvarna TS 148X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

TERMINAL COVER SERVICE AND ADJUSTMENTS NEGATIVE (BLACK) CABLE TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 44) • Raise hood. • Unsnap headlight wire connector. • Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. • To replace, reverse above procedure. POSITIVE (RED) CABLE HOOD Fig. 43 TO REPLACE LED HEADLIGHT • Raise hood. • Disconnect harness from LED light. • Remove mounting screws to remove LED light, reflector and lens. • Replace LED light, reflector, or lens as needed. • Reinstall using mounting screws previously removed. • Reconnect harness to LED light. • Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. TO REPLACE FUSE Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash. TRANSMISSION REMOVAL/REPLACEMENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and beforeoperatingthetractor. See"PURGETRANSMISSION" in the Operation section of this manual. HEADLIGHT WIRE CONNECTOR 07002 ENGINE Fig. 44 TO ADJUST THROTTLE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
25
TRANSMISSION
REMOVAL/REPLACEMENT
Should your transmission require removal for service or
replacement, it should be purged after reinstallation and
before operating the tractor.
See “PURGE TRANSMISSION”
in the Operation section of this manual.
SERVICE AND ADJUSTMENTS
TO REPLACE LED HEADLIGHT
•
Raise hood.
•
Disconnect harness from LED light.
•
Remove mounting screws to remove LED light, re
fl
ector
and lens.
•
Replace LED light, re
fl
ector, or lens as needed.
•
Reinstall using mounting screws previously removed.
•
Reconnect harness to LED light.
•
Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
•
Check wiring.
TO REPLACE FUSE
Replace with 20 amp automotive-type plug-in fuse.
The
fuse holder is located behind the dash.
POSITIVE
(RED)
CABLE
TERMINAL
COVER
NEGATIVE
(BLACK)
CABLE
Fig. 43
TO REMOVE HOOD AND GRILL ASSEMBLY
(See Fig. 44)
•
Raise hood.
•
Unsnap headlight wire connector.
•
Stand in front of tractor.
Grasp hood at sides, tilt toward
engine and lift off of tractor.
•
To replace, reverse above procedure.
Fig. 44
07002
HEADLIGHT
WIRE
CONNECTOR
HOOD
ENGINE
TO ADJUST THROTTLE CONTROL CABLE
The throttle control has been preset at the factory and
adjustment should not be necessary. If adjustment is nec-
essary, see engine manual.