Icom IC-V3500 Advanced Manual - Page 39

Bank Link scan, Example: Starting a Bank Link scan.

Page 39 highlights

4. SCAN OPERATION Memory Bank scan DDBank Link scan A Bank Link scan searches the linked banks. NOTE: To use a Bank Link scan, •• The Bank Link function must be turned ON and two or more Banks are linked in the Set mode. (p. 8-4) •• Two or more Memory channels, which are not set as Skip channels, must be entered into the linked banks. 1. Repeatedly push [M/CALL PRIO] to select the Memory mode. ••" " and the Memory Channel number are displayed. 2. Push [BANK OPT] to select the Memory Bank mode. ••" " and the bank letter blink. LLThe bank name is displayed, if set. 3. Rotate [DIAL] to select any bank. LLBanks that contain no Memory channels are skipped. 4. Push any key to exit the Memory Bank mode. ••" " and the bank letter are displayed. 5. Hold down [V/MHz SCAN] for 1 second to start scanning. ••The frequency decimal point and " " blink. LLWhen a signal is detected, the scan pauses according to the Scan Stop timer setting, and then resumes. LLPush [MONI ANM PA] to stop or resume the scan. 6. Push [V/MHz SCAN] to cancel the scan. TIP: During a scan, rotating [DIAL] changes the scanning direction. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN Example: Starting a SET MONI LOW TONE M/CALL Bank V/MHz Link scan. Repeatedly push [M/CALL PRIO] to select the Memory mode. DIGITAL PRIO AO BUSY MUTE NAR " " and the Memory Channel MID LOW LOCK ANM DUP T-SCAN PRIO SCAN number are displayed. SET MONI LOW TONE M/CALL V/MHz Push [BANK OPT] to enter the Memory Bank mode. DIGITAL PRIO AO BUSY MUTE NAR MID " " and the bank letter blink. LOW Rotate [DIAL] to select any bank. (Example: Bank A) MUTE NAR MID LOW DIGITAL PRIO AO BUSY Push any key to exit the Memory Bank mode. DIGITAL PRIO AO BUSY MUTE NAR " " and the bank letter are MID LOW LOCK ANM displayed. DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/MHz Hold down [V/MHz SCAN] for 1 second to start scanning. MUTE NAR MID LOW LOCK SET ANM MONI DIGITAL PRIO AO BUSY "." and " DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz " blink. MUTE NAR MID LOW LOCK SET ANM MONI PDRIGIOITAL AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz MUTE NAR MID LOW LOCK SET ANM MONI PDRIGIOITAL AO BUSY DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/ MHz 4-8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89

4-8
4.
SCAN OPERATION
Memory Bank scan
D
Bank Link scan
A Bank Link scan searches the linked banks�
NOTE:
To use a Bank Link scan,
The Bank Link function must be turned ON and
two or more Banks are linked in the Set mode�
(p� 8-4)
Two or more Memory channels, which are not set
as Skip channels, must be entered into the linked
banks�
1�
Repeatedly push [M/CALL PRIO] to select the
Memory mode�
•“
” and the Memory Channel number are displayed�
2�
Push [BANK OPT] to select the Memory Bank
mode�
•“
” and the bank letter blink�
L
The bank name is displayed, if set�
3�
Rotate [DIAL] to select any bank�
L
Banks that contain no Memory channels are skipped�
4�
Push any key to exit the Memory Bank mode�
•“
” and the bank letter are displayed�
5�
Hold down [V/MHz SCAN] for 1 second to start
scanning�
• The frequency decimal point and “
” blink�
L
When a signal is detected, the scan pauses
according to the Scan Stop timer setting, and then
resumes�
L
Push [MONI ANM PA] to stop or resume the scan�
6�
Push [V/MHz SCAN] to cancel the scan�
TIP:
During a scan, rotating [DIAL] changes the
scanning direction�
Example: Starting a Bank Link scan.
LOCK
S
E
T
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK
S
E
T
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK
S
E
T
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Hold down [V/MHz SCAN] for 1 second to start
scanning�
Push [BANK OPT] to enter the Memory Bank mode�
Rotate [DIAL] to select any bank� (Example: Bank A)
” and the Memory Channel
number are displayed�
Repeatedly push [M/CALL PRIO] to select the
Memory mode�
Push any key to exit the Memory Bank mode�
” and the bank letter are
displayed�
“�” and “
” blink�
” and the bank letter blink�