Icom M93D Instruction Manual - Page 16

PREPARATIONS, Entering the MMSI code, Entering

Get Icom M93D PDF manuals and user guides View all Icom M93D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

4 PREPARATIONS ■■Entering the MMSI code The Maritime Mobile Service Identity (MMSI: DSC self ID) code consists of 9 digits. You can only enter the code when turning ON the transceiver for the first time. This initial code entry can be done only once. After entering, it can be changed only by your dealer or distributor. If your MMSI code has already been entered, this entry is not necessary. 1. Hold down [ ] to turn ON the transceiver. ••Three short beeps sound, and "Push [ENT] to Register your MMSI" is displayed. 2. Push [ENT] to start entering the MMSI code. ••The "MMSI Input" screen is displayed. LPush [CLR] twice to skip the entry. If you skip the entry, you cannot make a DSC call. To enter the code after skipping, turn OFF the power, and then turn it ON again. 3. Enter the MMSI code. 4. Repeat step 3 to enter all 9 digits. 5. Push the software key below [DONE] to set the entered code. ••The "Confirmation" screen is displayed. 6. Enter your MMSI code again to confirm. 7. Push the software key below [DONE] to set the entered code. LWhen your MMSI code is successfully entered, "MMSI Successfully Registered" is briefly displayed, and then the operating screen opens. LYour MMSI code is also displayed on the operating screen. TIP: ••Select a number using [◄] and Push [ENT] to enter the selected number. ••Select "←" or "→," to move the cursor. 9 NOTE: For the Dutch and German versions, entering the ATIS ID is also required. See the next page for details.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
9
4
PREPARATIONS
■
Entering the
MMSI code
The Maritime Mobile Service Identity (MMSI: DSC self ID)
code consists of 9 digits. You can only enter the code when
turning ON the transceiver for the first time.
4.
Repeat step 3 to enter all 9 digits.
5.
Push the software key below [DONE] to set the entered
code.
•
The “Confirmation” screen is displayed.
This initial code entry can be done only once.
After entering, it can be changed only by your dealer
or distributor. If your MMSI code has already been
entered, this entry is not necessary.
1.
Hold down [
] to turn ON the transceiver.
• Three short beeps sound, and “Push [ENT] to Register your
MMSI” is displayed.
2.
Push [ENT] to start entering the MMSI code.
•
The “MMSI Input” screen is displayed.
L
Push [CLR] twice to skip the entry.
If you skip the entry, you cannot make a DSC call. To enter
the code after skipping, turn OFF the power, and then turn it
ON again.
3.
Enter the MMSI code.
TIP:
•
Select a number using [◄] and [►].
• Push [ENT] to enter the selected
number.
•
Select “←” or “→,” to move the
cursor.
NOTE:
For the Dutch and German versions, entering the
ATIS ID is also required. See the next page for details.
6.
Enter your MMSI code again to
confirm.
7.
Push the software key below
[DONE] to set the entered code.
L
When your MMSI code is successfully
entered, “MMSI Successfully
Registered” is briefly displayed, and
then the operating screen opens.
L
Your MMSI code is also displayed on
the operating screen.