Intel AXXRMS2LL080 Hardware User Guide - Page 23

Flash ROM, Boot Strap ROM (SEEPROM), Diagnostic Components, LED Placement and Function

Get Intel AXXRMS2LL080 PDF manuals and user guides View all Intel AXXRMS2LL080 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

• Allows multiple initiators to address a single target (in a fail-over configuration) through an expander. For more information, see http://www.lsi.com/. Note: Some of these chip features may not be supported by Intel® Integrated RAID Module RMS2LL040 and RMS2LL080. Flash ROM An 4-MB CFI-compliant flash ROM is used to accommodate RAID firmware and RAID BIOS Console 2 OpROM. Boot Strap ROM (SEEPROM) The serial bootstrap ROM is used to configure the LSI* LSISAS2008 Processor Chip before the server board configures the PCI Express* registers. The bootstrap ROM sets the Phase Lock Loop (PLL) dividers, bootstrap configuration, and so on. Diagnostic Components LED Placement and Function The Intel® RAID Module RMS2LL040 and RMS2LL080 contain the following LEDs: • One surface-mounted heartbeat ("DS1B1: SAS_HB_LED") LED (Green Color) to indicate LSISAS2008 activity. • Another surface-mounted system error ("DS1B2: SAS_FLT_LED") LED (Amber Color) to indicate a board error. SAS/SATA Connectors The SAS/SATA connector shown in the following figure is the standard 7-pin SATA internal connector used by the Intel® Integrated RAID Module RMS2LL040 and RMS2LL080. These pin-outs for the serial ATA connector are not compatible with the legacy PATA connector. Intel® RAID Module RMS2LL040 and RMS2LL080 Hardware User's Guide 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
Intel® RAID Module RMS2LL040 and RMS2LL080 Hardware User’s Guide
13
•
Allows multiple initiators to address a single target (in a fail-over configuration)
through an expander.
For more information, see
.
Note:
Some of these chip features may not be supported by Intel
®
Integrated RAID Module
RMS2LL040 and RMS2LL080.
Flash ROM
An 4-MB CFI-compliant flash ROM is used to accommodate RAID firmware and RAID
BIOS Console 2 OpROM.
Boot Strap ROM (SEEPROM)
The serial bootstrap ROM is used to configure the LSI* LSISAS2008 Processor Chip
before the server board configures the PCI Express* registers. The bootstrap ROM sets
the Phase Lock Loop (PLL) dividers, bootstrap configuration, and so on.
Diagnostic Components
LED Placement and Function
The Intel
®
RAID Module RMS2LL040 and RMS2LL080 contain the following LEDs:
•
One surface-mounted heartbeat (“DS1B1: SAS_HB_LED”) LED (Green Color) to
indicate LSISAS2008 activity.
•
Another surface-mounted system error (“DS1B2: SAS_FLT_LED”) LED (Amber
Color) to indicate a board error.
SAS/SATA Connectors
The SAS/SATA connector shown in the following figure is the standard 7-pin SATA
internal connector used by the Intel
®
Integrated RAID Module RMS2LL040 and
RMS2LL080. These pin-outs for the serial ATA connector are not compatible with the
legacy PATA connector.