Intel DH61CR DH61CR Technical Product Specification - Page 21

SATA Interfaces - windows xp

Get Intel DH61CR PDF manuals and user guides View all Intel DH61CR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Product Description 1.8 USB The board supports up to ten USB 2.0 ports. The port arrangement is as follows: • Four USB 2.0 ports are implemented with stacked back panel connectors (black) • Six USB 2.0 front panel ports are implemented through three dual-port internal headers All 10 USB ports are high-speed, full-speed, and low-speed capable. NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use a shielded cable that meets the requirements for full-speed devices. For information about The location of the USB connectors on the back panel The location of the front panel USB headers Refer to Figure 9, page 42 Figure 10, page 43 1.9 SATA Interfaces The board provides four 3 Gb/s SATA connectors, which support one device per connector. The underlying SATA functionality is transparent to the operating system. The SATA controller can operate in both legacy and native modes. In legacy mode, standard IDE I/O and IRQ resources are assigned (IRQ 14 and 15). In Native mode, standard PCI Conventional bus resource steering is used. Native mode is the preferred mode for configurations using the Windows* XP, Windows Vista*, and Windows 7* operating systems. For more information, see: http://www.serialata.org/. For information about The location of the SATA connectors Refer to Figure 10, page 43 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Product Description
21
1.8
USB
The board supports up to ten USB 2.0 ports.
The port arrangement is as follows:
•
Four USB 2.0 ports are implemented with stacked back panel connectors (black)
•
Six USB 2.0 front panel ports are implemented through three dual-port internal
headers
All 10 USB ports are high-speed, full-speed, and low-speed capable.
NOTE
Computer systems that have an unshielded cable attached to a USB port may not meet
FCC Class B requirements, even if no device is attached to the cable.
Use a shielded
cable that meets the requirements for full-speed devices.
For information about
Refer to
The location of the USB connectors on the back panel
Figure 9, page 42
The location of the front panel USB headers
Figure 10, page 43
1.9
SATA Interfaces
The board provides four 3 Gb/s SATA connectors, which support one device per
connector.
The underlying SATA functionality is transparent to the operating system.
The SATA
controller can operate in both legacy and native modes.
In legacy mode, standard IDE
I/O and IRQ resources are assigned (IRQ 14 and 15).
In Native mode, standard PCI
Conventional bus resource steering is used.
Native mode is the preferred mode for
configurations using the Windows* XP, Windows Vista*, and Windows 7* operating
systems.
For more information, see:
.
For information about
Refer to
The location of the SATA connectors
Figure 10, page 43