Intel Intel LanRover VPN Express V35 NA Installation Guide - Page 29

Using Bridge Mode With the LanRover VPN Gateway/LanRover

Get Intel Intel LanRover VPN Express V35 NA - LanRover VPN Express V35 NA PDF manuals and user guides
UPC - 735858121200
View all Intel Intel LanRover VPN Express V35 NA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Next Step Setting Up a Basic Routing Mode Configuration on a New Device Note: Only the Shiva VPN Manager uses this password. It is not used for Telnet, nor is it the console password; it is used as an encryption key to encrypt communications between the Shiva VPN Manager and the device. The factory-default manager user name is admin. Note: Passwords are case sensitive. 10. To set the time zone of the device, enter the time zone with respect to Greenwich Mean Time. For example, to set the time zone for Boston, enter: vpn1 (setup) # timezone est 5 edt 11. To set the Gateway's clock, use a 24-hour clock figure in the format YY DD HH MM SS. For example, to set the system clock to December 31, 2000, at 2:18 p.m., enter: vpn1 (setup) # clock-set 00 12 31 14 18 00 The device now asks you if you want to save the setup entries. 12. At the prompt, enter Y. 13. Test the interfaces using ping. At the prompt, enter ping and the full IP address of the E0 interface. vpn1 # ping 10.1.1.2 255.255.255.0 The device informs you of the success of the ping. Note: The initial ping has a success rate of 80 percent as the device must use the Address Resolution Protocol (ARP) to resolve the physical address of the destination IP address. 14. At the prompt, enter ping and the full IP address of the E1 interface: vpn1 # ping 10.1.2.2 255.255.0 The device informs you of the success of the ping. The setup script is now complete. The initial configuration is set on the new LanRover VPN Gateway/LanRover VPN Express. Using Bridge Mode With the LanRover VPN Gateway/LanRover VPN Express (page 3-8) LanRover VPN Gateway/LanRover VPN Express Installation and Upgrade Guide 3-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Setting Up a Basic Routing Mode Configuration on a New Device
LanRover VPN Gateway/LanRover VPN Express Installation and Upgrade Guide
3-7
Note:
Only the Shiva VPN Manager uses this password. It is not
used for Telnet, nor is it the console password; it is used as an
encryption key to encrypt communications between the Shiva
VPN Manager and the device. The factory-default manager user
name is
admin
.
Note:
Passwords are case sensitive.
10.
To set the time zone of the device, enter the time zone with respect
to Greenwich Mean Time. For example, to set the time zone for
Boston, enter:
vpn1 (setup) # timezone est 5 edt
11.
To set the Gateway’s clock, use a 24-hour clock figure in the
format YY DD HH MM SS. For example, to set the system clock
to December 31, 2000, at 2:18 p.m., enter:
vpn1 (setup) # clock-set 00 12 31 14 18 00
The device now asks you if you want to save the setup entries.
12.
At the prompt, enter
Y
.
13.
Test the interfaces using ping. At the prompt, enter
ping
and the
full IP address of the E0 interface.
vpn1 # ping 10.1.1.2 255.255.255.0
The device informs you of the success of the ping.
Note:
The initial ping has a success rate of 80 percent as the
device must use the Address Resolution Protocol (ARP) to
resolve the physical address of the destination IP address.
14.
At the prompt, enter
ping
and the full IP address of the E1
interface:
vpn1 # ping 10.1.2.2 255.255.0
The device informs you of the success of the ping.
The setup script is now complete. The initial configuration is set on the
new LanRover VPN Gateway/LanRover VPN Express.
Next Step
Using Bridge Mode With the LanRover VPN Gateway/LanRover
VPN Express (page 3-8)