Intel RS2WC040 Hardware User Guide - Page 31

English, Intel, Server Boards and Server Chassis Safety Information

Get Intel RS2WC040 PDF manuals and user guides View all Intel RS2WC040 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

English Read all caution and safety statements in this document before performing any of the instructions. See also Intel® Server Boards and Server Chassis Safety Information on the Resource CD and/or at http://support.intel.com/support/motherboards/server/sb/cs-010770.htm. The power button on the system does not turn off system AC power. To remove AC power from the system, you must unplug each AC power cord from the wall outlet or power supply. The power cord(s) is considered the disconnect device to the main (AC) power. The socket outlet that the system plugs into shall be installed near the equipment and shall be easily accessible. SAFETY STEPS: Whenever you remove the chassis covers to access the inside of the system, follow these steps: 1. Turn off all peripheral devices connected to the system. 2. Turn off the system by pressing the power button. 3. Unplug all AC power cords from the system or from wall outlets. 4. Label and disconnect all cables connected to I/O connectors or ports on the back of the system. 5. Provide some Electrostatic Discharge (ESD) protection by wearing an antistatic wrist strap attached to chassis ground of the system-any unpainted metal surface-when handling components. 6. Do not operate the system with the chassis covers removed. After you have completed the six SAFETY steps above, you can remove the system covers. To do this: 1. Unlock and remove the padlock from the back of the system if a padlock has been installed. 2. Remove and save all screws from the covers. 3. Remove the cover(s). For proper cooling and airflow, always reinstall the chassis covers before turning on the system. Operating the system without the covers in place can damage system parts. To install the covers: 1. Check first to make sure you have not left loose tools or parts inside the system. 2. Check that cables, add-in cards, and other components are properly installed. 3. Attach the covers to the chassis with the screws removed earlier, and tighten them firmly. 4. Insert and lock the padlock to the system to prevent unauthorized access inside the system. 5. Connect all external cables and the AC power cord(s) to the system. Intel® RAID Controller RS2WC040 Hardware User's Guide 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Intel® RAID Controller RS2WC040 Hardware User’s Guide
21
English
Read all caution and safety statements in this document before performing any of the
instructions. See also
Intel
®
Server Boards and Server Chassis Safety Information
on the
Resource CD and/or at
.
The power button on the system does not turn off system AC power.
To remove AC power from the system, you must unplug each AC
power cord from the wall outlet or power supply.
The power cord(s) is considered the disconnect device to the main
(AC) power. The socket outlet that the system plugs into shall be
installed near the equipment and shall be easily accessible.
SAFETY STEPS:
Whenever you remove the chassis covers to
access the inside of the system, follow these steps:
1.
Turn off all peripheral devices connected to the system.
2.
Turn off the system by pressing the power button.
3.
Unplug all AC power cords from the system or from wall
outlets.
4.
Label and disconnect all cables connected to I/O connectors
or ports on the back of the system.
5.
Provide some Electrostatic Discharge (ESD) protection by
wearing an antistatic wrist strap attached to chassis ground of
the system-any unpainted metal surface-when handling
components.
6.
Do not operate the system with the chassis covers removed.
After you have completed the six SAFETY steps above, you can
remove the system covers. To do this:
1.
Unlock and remove the padlock from the back of the system if
a padlock has been installed.
2.
Remove and save all screws from the covers.
3.
Remove the cover(s).
For proper cooling and airflow, always reinstall the chassis covers
before turning on the system. Operating the system without the
covers in place can damage system parts. To install the covers:
1.
Check first to make sure you have not left loose tools or parts
inside the system.
2.
Check that cables, add-in cards, and other components are
properly installed.
3.
Attach the covers to the chassis with the screws removed
earlier, and tighten them firmly.
4.
Insert and lock the padlock to the system to prevent
unauthorized access inside the system.
5.
Connect all external cables and the AC power cord(s) to the
system.