JVC HM-DH30000UP 84 pg. instruction manual on the HM-DH30000U D-VHS recorder/p - Page 23

Selecting monitor sound, Playing back tape repeatedly, Adjusting tracking condition

Page 23 highlights

C Playing back tape repeatedly - Repeat Playback You can play back a tape repeatedly (50 times). While playing back a tape, press and hold PLAY ( 3 ) for more than 5 seconds. The play indicator ( # ) on the front display panel starts flashing slowly, and a tape will be played back 50 times. To stop playback, press STOP ( 7 ) on the Remote or STOP/EJECT ( 7/0 ) on the front panel. NOTE: For a cassette recorded in D-VHS mode, Repeat Playback is possible only if the cassette was recorded in STD mode. D Adjusting tracking condition - Tracking Adjustments Automatic tracking adjustment This VCR automatically adjusts the tracking condition. Whenever you insert a tape and start playback, automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback. Manual tracking adjustment If automatic tracking cannot eliminate noises well during playback, use the manual tracking following the procedures below. ● You can also use the manual tracking during slow motion playback (੬ pg. 33). 1 Activate manual tracking Press CH + and - on the front panel at the same time during playback. 2 Eliminate the noises on the TV screen. Press CH + or -. ● Press it briefly for a fine adjustment, or press and hold for a coarse adjustment. Watch the screen and continue adjustment until optimum picture and sound quality are achieved. ● To reactivate automatic tracking, press CH + and - on the front panel at the same time. The automatic tracking becomes active again. EN 23 E Selecting monitor sound - Audio Monitor You can select the desired monitor sound. While playing back a tape on which stereo sound or SAP sound is recorded, press A. MONITOR on the Remote. Each time you press the button, sound changes as follows: S-VHS/VHS HI-FI HI-FI L HI-FI R NORM HI-FI NORM HI-FI: Normally select this. Hi-Fi sound is played back. HI-FI L: Sound on the left Hi-Fi channel is played back. HI-FI R: Sound on the right Hi-Fi channel is played back. NORM:Sound on the normal track is played back. NORM HI-FI: Both sounds on the Hi-Fi track and normal track are mixed and played back. D-VHS HI-FI HI-FI L HI-FI R HI-FI: Normally select this. HI-FI L: Sound on the left Hi-Fi channel is played back. HI-FI R: Sound on the right Hi-Fi channel is played back. NOTES: ● The above indication appears when "SUPERIMPOSE" is set to "ON" (੬ pg. 56), though the monitor sound changes in sequence. ● If the tape being played back has no Hi-Fi sound track, the normal sound track will be heard regardless of this setting.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84

EN
23
Selecting monitor sound
— Audio Monitor
You can select the desired monitor sound.
While playing back a tape on which stereo sound or SAP
sound is recorded, press A. MONITOR on the Remote.
Each time you press the button, sound changes as follows:
S-VHS/VHS
HI-FI:
Normally select this.
Hi-Fi sound is played back.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R: Sound on the right Hi-Fi channel is played back.
NORM:Sound on the normal track is played back.
NORM
HI-FI:
Both sounds on the Hi-Fi track and normal
track are mixed and played back.
D-VHS
HI-FI:
Normally select this.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R: Sound on the right Hi-Fi channel is played back.
NOTES:
The above indication appears when “SUPERIMPOSE” is set to
“ON” (
Z
pg. 56), though the monitor sound changes in
sequence.
If the tape being played back has no Hi-Fi sound track, the
normal sound track will be heard regardless of this setting.
C
D
Playing back tape repeatedly
— Repeat Playback
You can play back a tape repeatedly (50 times).
While playing back a tape, press and hold PLAY (
3
)
for more than 5 seconds.
The play indicator (
#
) on the front display panel starts
flashing slowly, and a tape will be played back 50 times.
To stop playback,
press
STOP (
7
)
on the Remote or
STOP/EJECT
(
7
/
0
)
on the front panel.
NOTE:
For a cassette recorded in D-VHS mode, Repeat Playback is
possible only if the cassette was recorded in STD mode.
Adjusting tracking condition
— Tracking Adjustments
Automatic tracking adjustment
This VCR automatically adjusts the tracking condition.
Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, use the manual tracking following the
procedures below.
You can also use the manual tracking during slow
motion playback (
Z
pg. 33).
1
Activate manual tracking
Press
CH
+
and
on the front panel at the same
time during playback.
2
Eliminate the noises on the TV screen.
Press
CH +
or
.
Press it briefly for a fine adjustment, or press and
hold for a coarse adjustment. Watch the screen
and continue adjustment until optimum picture
and sound quality are achieved.
To reactivate automatic tracking, press
CH +
and
on the front panel at the same time. The
automatic tracking becomes active again.
NORM
NORM HI-FI
HI-FI
HI-FI L
HI-FI R
E
HI-FI
HI-FI L
HI-FI R