Jabra JX-10 User Manual - Page 14

Press and hold, IMPORTANT, How to pair your Jabra Bluetooth Hub and headset, NOTE 1, NOTE 2 - reset

Get Jabra JX-10 - Bluetooth Headset PDF manuals and user guides
UPC - 607421734820
View all Jabra JX-10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

English • Connect the power supply to your Bluetooth Hub's power supply socket . • Connect the power supply to the wall power socket. • You can use the 'wire guide' at the bottom of the Bluetooth Hub to neatly guide the cable from the desk phone to the wall phone plug. When the LED is green move on to page 15 "Adjust setting with a test call from your desk phone" instructions. In the unlikely event that the Bluetooth Hub is not OK, its LED will flash red. • First, try disconnecting and reconnecting the Bluetooth Hub from the power source. • If the LED is still flashing red, you must reset your Bluetooth Hub. o Press and hold the Bluetooth Hub reset button . o The reset light will turn solid red for 3 seconds, and then turn green. o If the LED is still flashing red, after disconnect and reset, please contact your dealer. IMPORTANT: Following reset, you must pair your Bluetooth Hub and headset. How to pair your Jabra Bluetooth Hub and headset IMPORTANT: Your Bluetooth Hub and headset have been pre-paired at the factory, so this step is only necessary in the unlikely event that pairing has been lost, e.g. by resetting. • Set your headset into pairing mode by pressing its pairing button . The LED will show a steady blue light. • Set your Bluetooth Hub in pairing mode by pressing and holding its pairing button . The LED will show a steady blue light, and the two devices will 'search' for each other. NOTE: Both devices will continue to search for a pair for 5 minutes. • When your headset and Bluetooth Hub have paired successfully, the Bluetooth Hub LED will flash blue 10 times and then turn green and the headset LED will flash blue slowly. NOTE 1: If you accidentally put either the Bluetooth Hub or headset into pairing mode, tap the pairing button / to exit pairing mode. NOTE 2: To be able to use Voice Dial from your mobile phone, please note that you need to pair the Jabra JX10 headset with the Bluetooth Hub before you pair the headset to your mobile phone. One Bluetooth Hub can be paired with multiple headsets, just as one headset can be paired with multiple Bluetooth Hubs. Your headset will 'prioritize' the Bluetooth Hub it has been paired with most recently. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
•
Connect the power supply
to your Bluetooth Hub’s power supply socket
.
•
Connect the power supply
to the wall power socket.
•
You can use the ‘wire guide’ at the bottom of the Bluetooth Hub to neatly guide the
cable from the desk phone to the wall phone plug.
When the LED
is green move on to page 15 “Adjust setting with a test call from your
desk phone” instructions.
In the unlikely event that the Bluetooth Hub is not OK, its LED
will flash red.
•
First, try disconnecting and reconnecting the Bluetooth Hub from the power source.
•
If the LED
is still flashing red, you must reset your Bluetooth Hub.
o
Press and hold
the Bluetooth Hub reset button
.
o The reset light
will turn solid red for 3 seconds, and then turn green.
o If the LED is still flashing red, after disconnect and reset, please contact your dealer.
IMPORTANT:
Following reset, you must pair your Bluetooth Hub and headset.
How to pair your Jabra Bluetooth Hub and headset
IMPORTANT:
Your Bluetooth Hub and headset have been pre-paired at the factory, so this
step is only necessary in the unlikely event that pairing has been lost, e.g. by resetting.
•
Set your headset into pairing mode by pressing its pairing button
. The LED
will show
a steady blue light.
•
Set your Bluetooth Hub in pairing mode by pressing and holding its pairing button
.
The LED
will show a steady blue light, and the two devices will ‘search’ for each other.
NOTE:
Both devices will continue to search for a pair for 5 minutes.
•
When your headset and Bluetooth Hub have paired successfully, the Bluetooth Hub LED
will flash blue 10 times and then turn green and the headset LED
will flash blue slowly.
NOTE 1:
If you accidentally put either the Bluetooth Hub or headset into pairing mode, tap
the pairing button
/
to exit pairing mode.
NOTE 2:
To be able to use Voice Dial from your mobile phone, please note that you need
to pair the Jabra JX10 headset with the Bluetooth Hub before you pair the headset to your
mobile phone.
One Bluetooth Hub can be paired with multiple headsets, just as one headset can be
paired with multiple Bluetooth Hubs. Your headset will ‘prioritize’ the Bluetooth Hub it
has been paired with most recently.
14
English