Kenwood KAC-746 User Manual

Kenwood KAC-746 Manual

Get Kenwood KAC-746 PDF manuals and user guides View all Kenwood KAC-746 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood KAC-746 manual content summary:

  • Kenwood KAC-746 | User Manual - Page 1
    KAC-746 4-CHANNEL POWER AMPLIFIER INSTRUCTION MANUAL © B64-1176-00 (EM)
  • Kenwood KAC-746 | User Manual - Page 2
    you smell or see smoke, turn the power off immediately and consult your Kenwood dealer. • Do not touch the unit during use because the surface of • If you have difficulty in installing this unit in your vehicle, contact your Kenwood dealer. Cleaning the unit • If the surface is dirty, wipe it clean
  • Kenwood KAC-746 | User Manual - Page 3
    winkers, and wipers work properly. Installation Self-tapping screw (ø4 × 16 mm) Installation board, etc. (thickness : 15 mm or more) • Since the power amplifier has no parts which require operation, it can be installed at a position away from the driver's seat without any hindrances. As generally
  • Kenwood KAC-746 | User Manual - Page 4
    HPF 200 FREQUENCY(Hz) CONTROL B 4 CHANNEL POWER AMPLIFIER Amplifier A # $ % ^ Amplifier B 1 Fuse (30 A) 2 Battery terminal 3 Ground terminal 4 Power control (REMOTE) terminal 5 Amplifier A speaker output terminals 6 Amplifier B speaker output terminals 7 Speaker level input terminals 8 FREQUENCY
  • Kenwood KAC-746 | User Manual - Page 5
    the right as a guide. NOTE For the pre-output level or the maximum power output, refer to the "Specifications" in the instruction manual of the center unit. accidents or problems that can occur. When the protection function is triggered, the Power indicator goes off and the amplifier stops
  • Kenwood KAC-746 | User Manual - Page 6
    100 80 150 100 80 1.0 OFF 150 HPF LPF MIN R MAX STEREO MONO(Lch) L {R 50 LPF 200 50 HPF 200 FREQUENCY(Hz) CONTROL B 4 CHANNEL POWER AMPLIFIER A Right input (Red) B Right input (Red) RCA cable ground terminal 2CAUTION When using an RCA cable with Do not use this terminal for power source
  • Kenwood KAC-746 | User Manual - Page 7
    sPower and Speakers cable connection • If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery cable. • Do not allow the cord to directly contact the edge of the iron plate by using Grommets. Power control (REMOTE)
  • Kenwood KAC-746 | User Manual - Page 8
    System examples s Full-range 4-channel + Subwoofer system CENTER UNIT L L RA R L L B R R L A+B R LINE OUT Amplifier Switch setting 100 80 100 150 80 FILTER OPERATION 150 OFF HPF LPF 50 LPF 200 50 HPF 200 FREQUENCY(Hz) STEREO MONO(Lch) L+R CONTROL A
  • Kenwood KAC-746 | User Manual - Page 9
    Troubleshooting guide Often, what appears to be a malfunction is due to user error. Before calling for service, please consult the following table. Symptom No sound. (No sound from one side.) Cause • Input (or output) cables are disconnected. • Protection circuit may be activated. •
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
KAC-746
4-CHANNEL POWER AMPLIFIER
INSTRUCTION MANUAL
© B64-1176-00 (EM)