Home » Kenwood Manuals » Car Stereo Subwoofers » Kenwood SW10 » Manual Viewer

Kenwood SW10 Instruction Manual

Kenwood SW10 - KSC Car Subwoofer Manual

UPC - 019048175748

View all Kenwood SW10 manuals

Add to My Manuals
Save this manual to your list of manuals

Kenwood SW10 manual content summary:

Kenwood SW10 | Instruction Manual - Page 1
ENGLISH FRANÇAIS DEUTSCH NEDERLANDS KSC-SW10 POWERED ENCLOSED SUBWOOFER INSTRUCTION MANUAL CAISSON D'EXTRÊME GRAVE AMPLIFIE MODE D'EMPLOI GEKAPSELTER SUBWOOFER MIT VERSTÄRKER BEDIENUNGSANLEITUNG SUBWOOFER MET SPANNINGSCIRCUIT GEBRUIKSAANWIJZING SUBWOOFER CON AMPLIFICATORE E CASSA ISTRUZIONI PER
Kenwood SW10 | Instruction Manual - Page 2
the stipulated size can cause fires.) Check the display! To replace the fuse, refer to the vehicle instruction manual. • To prevent a short circuit when replacing a fuse, disconnect the wiring harness at first your dealer for information or service on this product. Model : KSC-SW10 Serial Number :
Kenwood SW10 | Instruction Manual - Page 3
Name 1 Fixture A Outside Shape Quantity No. Part Name Outside Shape Quantity 2 6 10-pin connector cord (6 m / 19 ft) 1 2 Fixture B Velcro tape 2 7 (Double-side adhesive/ 1 for Remote control) 3 Fixture C 1 8 Remote control (6 m / 19 ft) 1 4 Machine screw (M4 x 6) 8 9 RCA
Kenwood SW10 | Instruction Manual - Page 4
. After checking, connect the wire from the negative terminal of the battery. Terminals of Subwoofer POWER/SPEAKER INPUT terminal (for Speaker cords) REMOTE terminal LINE IN terminal (for RCA pin jack) Connecting the remote control unit Connect with the lock part of remote control jack facing down
Kenwood SW10 | Instruction Manual - Page 5
as well as this instruction manual. KSC-SW10 ENGLISH Examples The following shows a typical connection for effective car stereo enjoyment. Connect your system by referring to the example. If there is no power control terminal in the center unit, connect the blue/white wire to the accessory line
Kenwood SW10 | Instruction Manual - Page 6
of the center unit Front speaker Center unit KSC-SW10 RCA cord (Commercially available parts) 9 RCA cord When the center unit output is a single RCA jack, use an RCA cord that converts the output into the two RCA jacks as shown above. The subwoofer output will be halved if the conversion
Kenwood SW10 | Instruction Manual - Page 7
3 Fixture C 4 Machine screw x 2 6 10-pin connector cord 9 RCA cord 8 Remote control (Fig. 1) Fixing the subwoofer Flat installation 1 4 Machine screw x 4 1 Fixture A x 2 (Fig. 2) 1 Connect the 10-pin connector cord 6, RCA cord 9, and remote control 8 to the speaker unit. (Fig. 1) (When
Kenwood SW10 | Instruction Manual - Page 8
of each part (Remote control) PHASE switch (Phase select switch) FREQUENCY control knob (Cut-off frequency control knob) LEVEL control knob (Input sensitivity control knob) Power indicator (Power display light) Power indicator Red glows Light is OFF The illumination on the subwoofer turns on
Kenwood SW10 | Instruction Manual - Page 9
Troubleshooting guide Often, what appears to be a malfunction is due to user error. Before calling for service, please consult the following table. ENGLISH Problem Power cannot be turned on (the POWER indicator does not light). No sound Cause • The fuse is blown. • The remote control cord is