Kenwood TS-480SAT Operation Manual - Page 73
Tx Monitor, Tx Power, Time-out Timer, Transverter
View all Kenwood TS-480SAT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 73 highlights
TIME-OUT TIMER The Time-out Timer limits the time of each transmission. It is also useful to prevent a long accidental transmission. 1 Press [MENU/ F.LOCK], then turn the MULTI control to access Menu No. 22. 2 Press [ ]/ [ ] to select "oFF", "3", "5", "10", "20", or "30" minutes. 3 Press [MENU/ F.LOCK] to store the settings and exit Menu mode. TRANSVERTER If you have a transverter that converts the TS-480 operating frequencies to other frequencies, you can use this TS-480 transceiver as a transverter exciter. Consult the instruction manual that came with the transverter for interfacing to the TS-480 transceiver. ■ Frequency Display 1 Connect the transverter to the ANT 1 or ANT 2 connector from the TX/ RX unit. 2 Select the exciter operating frequency on the transceiver. • The transverter will use this frequency as the reference for converting frequencies. 3 Access Menu No. 23, and select "on". • The output power is automatically set to the lowest power for that frequency (default). Refer to "TX POWER" {below}. 4 Press [MENU/ F.LOCK] to store the setting and exit the Menu mode. 5 Press [ENT], then set the target converting frequency using the numeric keys. 6 Press [ENT] to complete the entry. 7 The transceiver displays the target transverter frequency instead of the actual operating frequency. Note: When using a transverter, not all the functions of this transceiver are available. ■ Transmission Output Power If Menu No. 23 is selected "on" {above}, the transceiver automatically decreases the output power to 5 watts. However, if you do not wish to decrease the output power, you can turn this function OFF. Access Menu No. 24 and select "oFF". The transceiver transmits at full power even if Menu No. 23 is ON {above}. 13 OPERATOR CONVENIENCES TX MONITOR TX monitor allows you to monitor the on-going transmission sound. This is convenient when you want to check the modulation sound quality of the transmission. In FSK mode, you can monitor the FSK signal that the transceiver is transmitting. 1 Press [PWR/ 4/ TX MON] (1 s). 2 The current TX monitor setting appears on the sub-display. 3 Turn the MULTI control to select the monitor sound level from "oFF", and "1" to "9". 4 Press [MTR/ CLR] to store the selected TX monitor level. Note: ◆ We recommend you use headphones when you monitor SSB, AM, or FM mode, in order to avoid howling. ◆ The CW transmission signal cannot be monitored using the TX monitor function. Use the TX sidetone function to monitor CW transmissions (Menu Nos. 13 and 34). TX POWER You can adjust the transmission output power by pressing [PWR/ 4/ TX MONI] and turning the MULTI control. If more precise power adjustment is required, access Menu No. 21 and select "on". When this function is activated, the power adjustment steps change as shown in the table below. TS-480SAT Band HF band 50 MHz Mode SSB/ CW/ FM/ FSK AM SSB/ CW/ FM/ FSK AM Menu No. 21 Menu No. 21 OFF ON 5 ~ 100 W 5 ~ 100 W in steps of 5 in steps of 1 5 ~ 25 W 5 ~ 25 W in steps of 5 in steps of 1 5 ~ 100 W 5 ~ 100 W in steps of 5 in steps of 1 5 ~ 25 W 5 ~ 25 W in steps of 5 in steps of 1 TS-480HX Band HF band 50 MHz Mode SSB/ CW/ FM/ FSK AM SSB/ CW/ FM/ FSK AM Menu No. 21 Menu No. 21 OFF ON 5 ~ 200 W 5 ~ 200 W in steps of 5 in steps of 1 5 ~ 50 W 5 ~ 50 W in steps of 5 in steps of 1 5 ~ 100 W 5 ~ 100 W in steps of 5 in steps of 1 5 ~ 25 W 5 ~ 25 W in steps of 5 in steps of 1 Note: ◆ The output power settings are stored independently for HF and 50 MHz. As shown in the table above, you can also store different output power settings for AM and other modes for HF bands and the 50 MHz band. ◆ If the TS-480HX transceiver is connected to the AT-300 external antenna tuner, the TX power is automatically reduced to 100 W (AM mode: 25 W). 65