Kenwood VR-5900 User Manual 1 - Page 46
Identifying Devices For PowerTouch III Control, How Do I Identify Devices?
View all Kenwood VR-5900 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 46 highlights
Chapter Two : Setting Up PowerTouch III Identifying Devices For PowerTouch III Control Remote Setup Once your speakers are set up and configured, you must identify your component devices to PowerTouch III. PowerTouch III can be set up to control any device: if the device code is not already part of PowerTouch III's extensive library, you can use the Learn feature to teach the device's commands to PowerTouch III. You can also use this Learn function to expand the control capabilities of existing codes. For more information, see "To Customize the PowerTouch III Screen" on page 43. How Do I Identify Devices? 1. Make sure you have installed batteries and chosen a model type (see page 34 - 35). 2. Touch (SETUP) on the Quick Access menu to access the Setup menu. 3. Touch on the Setup menu to access the IR 40 Setup menu: 4. Refer to "Noting Your Devices" on page 3 where you noted which device was connected to which jack set. 5. Touch to open the list of available jack sets: • CD1 • CD2/TAPE2 • MD/TAPE1 • CD-R • VIDEO1 through VIDEO4 • DVD • AV AUX • TV1 and TV2 (these allow PowerTouch III to control your TV or cable tuner, even if it isn't connected to one of the receiver's input jack sets). Touch the name of the jack set you want to set up. 6. Touch to select the type of device you have connected to the jack set. 7. Touch to select the device's brand. 8. Touch . You can now choose from a list of all the codes available for the device. Touch the first code on the list. • If the Kenwood devices are connected with a system control cable, be sure to select the code preceded by "Sys-" or "System". This instructs PowerTouch III to send all commands for the device to the receiver, which will control the device via the system control cable. • If you have a Kenwood Dual-Play 200-Disc CD Changer, you will need to set both CD1 and CD2/ TAPE2 to the correct code for this device ("SysMega"). 9. Touch . This instructs PowerTouch III to send a "power" test signal to the device. If your device turns on, the code you entered was correct. If it does not turn on, try the next code in the list. Continue until one of the codes works. If none of the codes work, see "To Customize the PowerTouch III Screen" on page 43. If you enter a code preceded by "Sys-" or "System" on step 8, skip this step. 10. When you have a code that works, touch . Check off that device on your list. Repeat steps 5 through 10 for each input until you are finished identifying devices to PowerTouch III. When you are done, turn to "How Do I Operate Devices?" on page 35 of the Users' Guide and note which icon corresponds to which connected device. How Do I Replace a Setup Code with a New One? If you purchase a new device to replace an existing device, you will need to identify the new device to PowerTouch III. To do so: 1. Connect the device as described in the appropriate section of Chapter One of this manual. 2. Follow the steps under "How Do I Identify Devices?" on this page for that input. The new code will replace the old code. How Do I Delete Setup Codes? If you disconnect a device and do not plan to replace it, you may want to delete the setup code from PowerTouch III. To do so: 1. Follow the steps under "How Do I Identify Devices?" on this page to select a jack set. 2. Touch . Scroll to the device "Nothing" then touch it. That device is no longer controlled by PowerTouch III. Example of device button display When a device is identified, its icon will be displayed among the device buttons. The TUNER and PHONO icons are displayed by default. Example with the CD1 device button: Icon of identified device (CD) This mark indicates that pressing the icon button of the identified device (CD) displays the next screen (the control screen) for the device.