KitchenAid KBHS109BSS Installation Guide - Page 3
Grounding Instructions, Save These Instructions - dimensions
View all KitchenAid KBHS109BSS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
Cabinet Dimensions 27" (68.6 cm) and 30" (76.2 cm) Microwave Ovens A D F B G E C 27" (68.6 cm) models A. 27" (68.6 cm) min. cabinet width B. 18⁵⁄₈" (47.3cm) from bottom of cutout to bottom of upper cabinet door C. 40" (101.6 cm) bottom of cutout to floor (recommended) D. 25¹⁄₂" (64.8 cm) cutout width E. 1¹⁄₂" (3.8 cm) min. bottom of cutout to top of cabinet door F. 17⁵⁄₈" (44.7 cm) recommended cutout height (will fit cutout height from 17³⁄₈" [44.1 cm] to 17³⁄₄" [45.1 cm]) G. 21⁷⁄₈" (55.5 cm) min. cutout depth 30" (76.2 cm) models A. 30" (76.2 cm) min. cabinet width B. 18⁵⁄₈" (47.3cm) from bottom of cutout to bottom of upper cabinet door C. 40" (101.6 cm) bottom of cutout to floor (recommended) D. 28¹⁄₂" (72.4 cm) cutout width E. 1¹⁄₂" (3.8 cm) min. bottom of cutout to top of cabinet door F. 17⁵⁄₈" (44.7 cm) recommended cutout height (will fit cutout height from 17³⁄₈" [44.1 cm] to 17³⁄₄" [45.1 cm]) G. 21⁷⁄₈" (55.5 cm) min. cutout depth Minimum Installation Clearances For proper installation, the following minimum clearances must exist above and below the cabinet opening. Installation Above Single Built-In Oven A 1" (2.5 cm) 1" (2.5 cm) from top of oven B A. Upper cabinet B. Lower single oven Approved models: KEBK171B, KEBK101B, KEBS179B, KEBS109B and KEBU109B. Electrical Requirements GROUNDING INSTRUCTIONS For a permanently connected microwave oven: The microwave oven must be connected to a grounded, metallic, permanent wiring system, or an equipment grounding conductor should be run with the circuit conductors and connected to the equipment grounding terminal or lead on the microwave oven. SAVE THESE INSTRUCTIONS If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes. Check with a qualified electrical installer if you are not sure the microwave oven is properly grounded. This microwave oven must be connected to a grounded metal, permanent wiring system. Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all local codes and ordinances. A copy of the above code standards can be obtained from: National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169-7471 CSA International 8501 East Pleasant Valley Road Cleveland, OH 44131-5575 Electrical Connection To properly install your microwave oven, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. ■ Microwave oven must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located underneath the control panel, along the oven vent. A A. Model/serial number plate ■ The microwave oven rated 120/240 volt, 20-amp, has 4 wires (L1, L2, N and G) in the flex conduit and should be connected to a 20-amp maximum rated circuit, overcurrent protected on both the L1 and L2 circuits. ■ A time-delay fuse or circuit breaker is recommended. ■ Flexible cable from the microwave oven should be connected directly to the junction box. ■ Do not cut the conduit. The length of conduit provided is for serviceability of the microwave oven. ■ A UL listed or CSA approved conduit connector must be provided. 3