KitchenAid KODE900HSS Installation Instructions - Page 15

Prepare Built-In Oven

Get KitchenAid KODE900HSS PDF manuals and user guides View all KitchenAid KODE900HSS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

5. The bottom vent and bottom vent trim (required when the oven is installed with the feet in the tall position) are shipped in the foam packing at the top of the oven. To install only the bottom vent, see the following instructions. To install both the bottom vent and the bottom vent trim for installations with the feet in the tall position, see the instructions in Step 6. ■■ Align vent tab (B) with oven frame (A) as shown. ■■ Using one #8-18 x 3/8" (9.5 mm) screw (D) on each side of the vent tab (B), fasten the vent securely to the oven. ■■ Align vent tab (B) with oven frame (A) as shown. ■■ Using one #8-18 x 3/8" (9.5 mm) screw (E) on each side of the vent tab (B), fasten the vent securely to the oven. A B A B D A. Oven frame B. Vent tab C C. Oven vent D. #8-18 x 3/8" (9.5 mm) screws 6. On models with the feet installed in the tall position, the bottom vent trim must also be installed. See the following instructions to install. ■■ Flex the upper vent piece (C) away from the lower vent piece (D) to slide the bottom vent trim (B) between them. Some force may be required to flex the upper vent trim (C) away from the lower vent trim (D). Some force may also be required to flex the bottom vent trim (B) and slide it into position. Make sure screw holes are properly aligned between the 2 pieces. See the following illustration. ■■ Install the bottom vent trim (B) to the lower vent piece (D) using two #8-18 x 1/4" (6.4 mm) screws on each side. E D A. Oven frame B. Vent tab C. Oven vent C D. Bottom vent trim E. #8-18 x 3/8" (9.5 mm) screw 7. Replace the oven racks. 8. Replace the oven door. See the "Replace Oven Door(s)" section. 9. Check that the door is free to open and close. If it is not, repeat the removal and installation procedures. See the "Prepare Built-In Oven" section. 10. Repeat for lower oven door. 11. Reconnect power. 12. The display panel will light and boot up. 13. If the display panel does not light, reference the "Warranty" section of the Use and Care Guide. B C A B D A C D A. #8-18 x 1/4" (6.4 mm) screw B. Bottom vent trim C. Upper vent piece D. Lower vent piece 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
15
5.
The bottom vent and bottom vent trim (required when
the oven is installed with the feet in the tall position)
are shipped in the foam packing at the top of the oven.
To install only the bottom vent, see the following instructions.
To install both the bottom vent and the bottom vent trim
for installations with the feet in the tall position, see the
instructions in Step 6.
■
Align vent tab (B) with oven frame (A) as shown.
■
Using one #8-18 x
3
/
8
" (9.5 mm) screw (D) on each side of
the vent tab (B), fasten the vent securely to the oven.
6.
On models with the feet installed in the tall position, the
bottom vent trim must also be installed. See the following
instructions to install.
■
Flex the upper vent piece (C) away from the lower vent
piece (D) to slide the bottom vent trim (B) between them.
Some force may be required to flex the upper vent trim (C)
away from the lower vent trim (D). Some force may also
be required to flex the bottom vent trim (B) and slide it
into position. Make sure screw holes are properly aligned
between the 2 pieces. See the following illustration.
■
Install the bottom vent trim (B) to the lower vent piece (D)
using two #8-18 x
1
/
4
" (6.4 mm) screws on each side.
■
Align vent tab (B) with oven frame (A) as shown.
■
Using one #8-18 x
3
/
8
" (9.5 mm) screw (E) on each side of
the vent tab (B), fasten the vent securely to the oven.
7.
Replace the oven racks.
8.
Replace the oven door. See the “Replace Oven
Door(s)” section.
9.
Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See the
“Prepare Built-In Oven” section.
10.
Repeat for lower oven door.
11.
Reconnect power.
12.
The display panel will light and boot up.
13.
If the display panel does not light, reference the
“Warranty” section of the Use and Care Guide.
A
B
C
D
A. Oven frame
B. Vent tab
C. Oven vent
D. #8-18 x
3
/
8
" (9.5 mm)
screws
D
A
A
C
B
D
B
C
A. #8-18 x
1
/
4
" (6.4 mm)
screw
B. Bottom vent trim
C. Upper vent piece
D. Lower vent piece
E
D
C
B
A
A. Oven frame
B. Vent tab
C. Oven vent
D. Bottom vent trim
E. #8-18 x
3
/
8
" (9.5 mm)
screw