KitchenAid KUIO18NNXS Use & Care Guide - Page 8
Connect Water Supply, Drain Connection
UPC - 883049221809
View all KitchenAid KUIO18NNXS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
Connect Water Supply Read all directions before you begin. IMPORTANT: ■ Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and ordinances. ■ Use copper tubing and check for leaks. ■ Install tubing only in areas where temperatures will remain above freezing. Tools needed: Gather the required tools and parts before starting installation. ■ Flat-blade screwdriver and ¹⁄₂" open-end wrenches or two adjustable wrenches nut driver NOTE: Do not use a piercing-type or 4.76 mm) saddle valve which reduces water flow and clogs more easily. Connecting the Water Line 1. Turn off main water supply. Turn on nearest faucet long enough to clear line of water. 2. Using a ¹⁄₂" copper supply line with a quarter-turn shutoff valve or the equivalent, connect the ice maker as shown. NOTE: To allow sufficient water flow to the ice maker a minimum ¹⁄₂" size copper supply line is recommended. 5. Bend the copper tubing to meet the water line inlet which is located on the back of the ice maker cabinet as shown. Leave a coil of copper tubing to allow the ice maker to be pulled out of the cabinet or away from the wall for service. REAR VIEW A B C D A. Water supply tube clamp B. Vent hose (drain pump models only) C. Inlet water tube clamp and supply line connector D. Drain hose (drain pump models only) 6. Remove and discard the short, black plastic tube from the end of the water line inlet. 7. Thread the nut onto the end of the tubing. Tighten the nut by hand. Then tighten it with a wrench two more turns. Do not overtighten. NOTE: To avoid rattling, be sure the copper tubing does not touch the cabinet's side wall or other parts inside the cabinet. A B A. Bulb B. Nut 3. Now you are ready to connect the copper tubing. Use ¹⁄₄" (6.35 mm) OD soft copper tubing for the cold water supply. ■ Ensure that you have the proper length needed for the job. Be sure both ends of the copper tubing are cut square. ■ Slip the compression sleeve and compression nut on the copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with an adjustable wrench. Do not overtighten. AB C A. Compression sleeve B. Compression nut C. Copper tubing 4. Place the free end of the tubing into a container or sink, and turn on main water supply and flush out tubing until water is clear. Turn off shutoff valve on the water pipe. NOTE: Always drain the water line before making the final connection to the inlet of the water valve to avoid possible water valve malfunction. AB C D A. Line to ice maker B. Nut (purchased) C. Ferrule (purchased) D. Supplied line from ice maker 8. Install the water supply tube clamp around the water supply line to reduce strain on the coupling. 9. Turn shutoff valve ON. 10. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak. Drain Connection Gravity Drain System Connect the ice maker drain to your drain in accordance with all state and local codes and ordinances. If the ice maker is provided with a gravity drain system, follow these guidelines when installing drain lines. This will help keep water from flowing back into the ice maker storage bin and potentially flowing onto the floor causing water damage. ■ Drain lines must have a minimum of 15.88 mm) inside diameter. ■ Drain lines must have a 1" drop per 48" (2.54 cm drop per 122 cm) of run or ¹⁄₄" drop per 12" (6.35 mm per 30.48 cm) of run and must not have low points where water can settle. ■ The floor drains must be large enough to accommodate drainage from all drains. 8