Konica Minolta Fujitsu fi-7280 Getting Started Guide - Page 6

Test-Scan, If the [Found New Hardware] dialog box

Get Konica Minolta Fujitsu fi-7280 PDF manuals and user guides View all Konica Minolta Fujitsu fi-7280 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

3. Connect the AC cable to the AC adapter (hereinafter called the "power cable"). WARNING Only use the supplied power cable. To prevent electrical shock or scanner malfunction, do not perform the following: zUse a different power cable zUse the supplied power cable for other devices 4. Connect the power cable to the power connector of the scanner and the power outlet. HINT When you plug the cable into the outlet, the [Power] button on the scanner's operator panel will flash once. Note that this is an initial diagnosis and not a malfunction. Test-Scan Follow the procedure described below to check that documents can be scanned correctly by using PaperStream Capture and the PaperStream IP (TWAIN) driver. 1. Press the [Power] button on the operator panel. LCD LED indicator Check Menu Stop/Clear Scan/Enter Power [Power] button D The scanner is turned on, and the [Power] button lights in green. During initialization, the following image is displayed on the LCD of the operator panel. The scanner is ready to scan when [Ready] is displayed. ATTENTION If [Ready] is not displayed on the LCD, refer to "Chapter 8 Troubleshooting" in the Operator's Guide. 2. Select the language to be displayed on the LCD. For details, refer to "Chapter 4 How to Use the Operator Panel" in the Operator's Guide. 3. Turn on the computer. D The scanner is automatically detected. ATTENTION If the [Found New Hardware] dialog box appears, select [Locate and install driver software (recommended)], and follow the instructions on the screen to install the driver. 4. Load a document in the scanner. 1. Pull out the chute extensions according to the length of the document. 2. Pull the stacker out, slide stacker extension 1 and stacker extension 2 toward you according to the length of the document, and lift the stopper up. 3. Load the document face-down in the ADF paper chute (Feeder). 4. Adjust the side guides to the width of the document. zfi-7160/fi-7180 Side guides Chute extension 2 Chute extension 1 Stacker Stopper zfi-7260/fi-7280 Chute extension 2 Chute extension 1 Stacker extension 1 Stacker extension 2 Side guides Stopper Stacker 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
6
3.
Connect the AC cable to the AC adapter
(hereinafter called the "power cable").
4.
Connect the power cable to the power
connector of the scanner and the power
outlet.
Test-Scan
Follow the procedure described below to check
that documents can be scanned correctly by using
PaperStream Capture and the PaperStream IP
(TWAIN) driver.
1.
Press the [Power] button on the operator
panel.
D
The scanner is turned on, and the [Power]
button lights in green.
During initialization, the following image is
displayed on the LCD of the operator
panel.
The scanner is ready to scan when
[Ready] is displayed.
2.
Select the language to be displayed on the
LCD.
For details, refer to "Chapter 4 How to Use
the Operator Panel" in the Operator's Guide.
3.
Turn on the computer.
D
The scanner is automatically detected.
4.
Load a document in the scanner.
1.
Pull out the chute extensions according to the
length of the document.
2.
Pull the stacker out, slide stacker extension 1
and stacker extension 2 toward you
according to the length of the document, and
lift the stopper up.
3.
Load the document face-down in the ADF
paper chute (Feeder).
4.
Adjust the side guides to the width of the
document.
z
fi-7160/fi-7180
z
fi-7260/fi-7280
WARNING
Only use the supplied power cable.
To prevent electrical shock or scanner
malfunction, do not perform the following:
z
Use a different power cable
z
Use the supplied power cable for other
devices
HINT
When you plug the cable into the outlet, the
[Power] button on the scanner’s operator
panel will flash once. Note that this is an
initial diagnosis and not a malfunction.
ATTENTION
If [Ready] is not displayed on the LCD,
refer to "Chapter 8 Troubleshooting" in the
Operator's Guide.
Menu
Scan/Enter
Check
Power
Stop/Clear
LCD
[Power]
button
LED indicator
ATTENTION
If the [Found New Hardware] dialog box
appears, select [Locate and install driver
software (recommended)], and follow the
instructions on the screen to install the
driver.
Chute
extension 1
Chute
extension 2
Stacker extension 1
Stacker
Side guides
Stacker extension 2
Stopper
Chute extension 1
Chute extension 2
Stacker
Side guides
Stopper