Kyocera KM-2560 IB-40/IB-40 (Type H) Installation Instructions - Page 1
Kyocera KM-2560 Manual
View all Kyocera KM-2560 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
English Installation Guide for IB-40/IB-40 (Type-H) (IPv6-IPv4 converter) Français Guide d'installation du IB-40/IB-40 (Type-H) (convertisseur IPv6-IPv4) Español Guía de instalación para el IB-40/IB-40 (Type-H) (convertidor Ipv6-Ipv4) Deutsch Installationsanleitung für IB-40/IB-40 (Type-H) (IPv6-IPv4-Konverter) Italiano Guida all'installazione di IB-40/IB-40 (Type-H) (convertitore IPv6-IPv4) IB-40/IB-40(Type-H) (IPv6-IPv4 IB-40 A IB-40 (Type-H) C B 3050/4050/5050 2560/3060 OPT2 D 1 A 2 1 OPT2 2 A 3050/4050/5050 4 2560/3060 4 B 6 OPT2 5 3 B 6 OPT2 3 5 Supplied parts A IB-40 1 B Cable 1 C IB-40 (Type-H 1 D Cable (Type-H 1 ・For installing into the HDD slot of printing system of 6030/8030, use IB-40 (Type-H). ・Since incorrect insertion of IB-40 and IB-40 (TypeH) causes breakdown of the product, take care when installing. Precautions ・The number of connector pins is different between IB-40 (A) and IB-40 (Type-H) (C). IB-40 (A): 60 pins; IB-40 (Type-H) (C): 40 pins ・Be sure to turn the MFP switch off and unplug the MFP from the power supply before installing a network interface card. ・Do not touch the PWB mounting surface with bare hands or something with static electricity. [When installing in 3050/4050/5050/2560/3060] 1. Remove the two screws (1) and then remove the OPT2 cover. 2. Insert IB-40 (A) along the OPT2 rail so that the marking (2) is oriented as shown in the figure and secure it with the two screws (1) that have been removed in step 1. 3. Connect the cable (B) to the MFP connector (3) and the connector (4). 4. Connect the LAN cable (6) to the LAN connector (5). Pièces fournies A IB-40 1 B Câble 1 C IB-40 (Type-H 1 D Câble (Type-H 1 ・Pour l'installation dans le logement du disque dur du système d'impression du 6030/8030, utiliser le IB-40 (Type-H). ・Effectuer l'installation avec le plus grand soin, car si le IB-40 et le IB-40 (Type-H) sont mal insérés, le produit risquera de tomber en panne. Piezas suministradas A IB-40 1 B Cable 1 C IB-40 (Type-H 1 D Cable (Type-H 1 ・Para instalarlo en la ranura HDD del sistema de impresión del 6030/8030, use el IB-40 (Type-H). ・Como la inserción incorrecta del IB-40 e IB-40 (Type-H) causa el rompimiento del producto, instálelos con sumo cuidado. Précautions ・Le IB-40 (A) et le IB-40 (Type-H) (C) possèdent un nombre de broches de connecteur différent. IB-40 (A): 60 broches; IB-40 (Type-H) (C): 40 broches ・Veiller à mettre l'interrupteur principal du MFP hors tension et à débrancher le MFP de la prise secteur avant d'installer une carte d'interface de réseau. ・Ne pas toucher la surface de montage du PWB avec les mains nues ou avec un objet chargé d'électricité statique. Precauciones ・El número de clavijas de conector es diferente entre IB-40 (A) e IB-40 (Type-H) (C). IB-40 (A): 60 clavijas; IB-40 (Type-H) (C): 40 clavijas ・Asegúrese de apagar el MFP y desenchúfelo del suministro de red eléctrica antes de instalar una tarjeta de interfaz de red. ・No toque la superficie de montaje de la PWB con las manos desnudas, o algo con electricidad estática. [Installation sur les modèles 3050/4050/5050/2560/3060] 1. Retirer les deux vis (1), puis le couvercle OPT2. 2. Insérer le IB-40 (A) le long du rail de l'OPT2 de façon que le repère (2) soit orienté comme indiqué sur l'illustration, et le fixer à l'aide des deux vis (1) retirées à l'étape 1. 3. Connecter le câble (B) au connecteur du MFP (3) et au connecteur (4). 4. Connecter le câble LAN (6) au connecteur LAN (5). [Cuando instale en 3050/4050/5050/2560/3060] 1. Quite dos tornillos (1) y desmonte la cubierta OPT2. 2. Inserte el IB-40 (A) a lo largo del riel OPT2, de manera que la marca (2) esté orientada como se ilustra en la figura, y asegúrela con los dos tornillos (1) que fueron quitados en el paso 1. 3. Conecte el cable (B) a los conectores (3) y (4) de MFP. 4. Conecte el cable de LAN (6) al conector de LAN (5). Gelieferte Teile A IB-40 1 B Kabel 1 C IB-40 (Type-H 1 D Kabel (Type-H 1 ・Für den Einbau in den HDD-Steckplatz des Drucksystems 6030/8030 ist IB-40 (Type-H) zu verwenden. ・Da falscher Einschub von IB-40 und IB-40 (Type-H) einen Ausfall des Produkts verursacht, lassen Sie bei der Installation Sorgfalt walten. Parti di fornitura A IB-40 1 B Cavo 1 C IB-40 (Type-H 1 D Cavo (Type-H 1 ・Per l'installazione nell'alloggiamento per HDD di un sistema di stampa 6030/8030, utilizzare l'IB-40 (Type-H). ・L'errato inserimento di IB-40 e IB-40 (Type-H) provoca danni al prodotto. Prestare particolare attenzione durante l'installazione. 同梱品 A IB-40 1 B 1 C IB-4(0 Type-H 1 D Type-H 1 ・6030/8030 HDD IB-40(Type-H IB-40 と IB-40(Type-H Vorsichtsmaßnahmen ・Die Zahl der Steckerstifte ist unterschiedlich zwischen IB-40 (A) und IB-40 (Type-H) (C). IB-40 (A): 60 Stifte; IB-40 (Type-H) (C): 40 Stifte ・Schalten Sie den MFP-Schalter aus, und trennen Sie den MFP von der Stromquelle, bevor Sie eine Netzwerk-Schnittstellenkarte installieren. ・Berühren Sie die Platinen-Montagefläche nicht mit bloßen Händen oder Gegenständen mit statischer Elektrizität. Precauzioni ・Il numero dei pin di connessione di IB-40 (A) e IB40 (Type-H) (C) è diverso. IB-40 (A): 60 pin; IB-40 (Type-H) (C): 40 pin ・Assicurarsi di aver spento l'interruttore dell'MFP e di aver sfilato la spina dell'MFP dalla presa prima di installare una scheda di interfaccia di rete. ・Non toccare la superficie di contatto della scheda a circuito stampato (PWB) con le mani nude od oggetti che producono elettricità statica. 注意事項 ・IB-40(A)と IB-40(Type-H)(C IB-40(A):60 ピン /IB-40(Type-H)(C):40 ピン MFP OFF [Bei Einbau in 3050/4050/5050/2560/3060] 1. Die zwei Schrauben (1) herausdrehen, und dann die Abdeckung OPT2 entfernen. 2. IB-40 (A) entlang der OPT2-Schiene so einschieben, dass die Markierung (2) gemäß der Abbildung ausgerichtet ist, und mit den in Schritt 1 entfernten zwei Schrauben (1) befestigen. [Quando si installa nel 3050/4050/5050/2560/3060] 1. Rimuovere le due viti (1), quindi rimuovere il coperchio OPT2. 2. Inserire l'IB-40 (A) lungo la scanalatura OPT2 in modo che le scritte (2) siano orientate come mostrato nella figura e fissare con le due viti (1) rimosse nell'operazione 1. [3050/4050/5050/2560/3060 1. ビス (1)2 OPT2 2. IB-40(A 2 OPT2 1 1)2 3. Das Kabel (B) an den MFP-Steckverbinder (3) und den Steckverbinder (4) anschließen. 4. Das LAN-Kabel (6) an den LAN-Anschluss (5) anschließen. 3. Collegare il cavo (B) al connettore MFP (3) e al connettore (4). 4. Collegare il cavo LAN (6) al connettore LAN (5). 3 B) を、MFP 3 4 4. LAN 5) に LAN 6 2008. 9 303MF56710