Home » Kyocera Manuals » Multifunction Devices » Kyocera TASKalfa 3501i » Manual Viewer

Kyocera TASKalfa 3501i PRESCRIBE Commands Technical Reference Manual - Rev. 4. - Page 145

HP LaserJet Emulation (Mode 6

View all Kyocera TASKalfa 3501i manuals

Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

HP LaserJet Emulation (Mode 6) HP LaserJet Emulation (Mode 6) On shipment from the factory, the printing system is set to power up in the HP LaserJet (PCL 6) emulation. The factory default symbol set is PC-8. To change this default symbol set, use the FRPO command with the U6 and U7 parameters. The default font is Courier. To set the printing system to power up in LaserJet mode, send the following PRESCRIBE command: !R! FRPO P1, 6; FRPO P3, 1; EXIT; To use the TimesNewRoman font of 14.25 points as the default font, add the following lines: FRPO V3, 'TimesNewRoman'; FRPO V1, 14; FRPO V2, 25; See Chapter 6 for details of the FRPO V parameters. The symbol set can be changed after power-up with the CSET or INTL command, or from the operator panel keys, or with LaserJet symbol sets typically accessed through software. The printing system also supports as many HP symbol sets as the LaserJet regularly supports and still other symbol sets can be provided in downloaded fonts. (A full list of the supported symbol sets appear in section LaserJet Symbol Sets on page 37.) These symbol sets can be used by appropriate font selection commands as explained below. Fonts can be selected with PRESCRIBE commands, or through the printer driver provided with your software. The following font sample was created through driver support. 7-33

Section	Page
General Infomation	3
Introduction	5
About the Technical Reference manual	6
Table of Contents	7
Introduction to PRESCRIBE	9
Format of PRESCRIBE Commands	12
Basic Concepts	12
Edge Limits	12
Margins	12
Page Orientation and Direction	13
Coordinate Systems	15
Text Positioning	15
Character Spacing	16
Paths	17
Logical Page and Physical Page	17
Command Parameters	18
Numeric Parameters	18
Character Strings	19
Upper and Lowercase Letters	20
Special Parameters	21
Graphics Tutorial	23
Drawing Lines	24
Drawing Boxes and Circles	28
Drawing Filled Shapes	31
Drawing Pie Charts	36
Path Mode Graphics	38
Path	38
Drawing Lines	40
Miter Limit	43
Dash Type	44
Drawing Arcs and Curves	46
Drawing Complex Curves	48
Closed Paths	51
Filled Areas	52
Clipping Rectangle	54
Printing with Character Paths	55
Raster Graphics	56
Raster Data Compression Formats	56
Commands for Printing Raster Data	57
Printing Raster Data	59
Changing the Printing System’s Imaging Model	59
Saving and Restoring the Graphics State	61
Macros	63
Examples of Macros	65
Fonts	69
List of Fonts	70
KPDL Fonts	72
Substituting a Bitmap Font	74
Font Selection	75
Font Selection by PRESCRIBE Commands	75
Placement of Font Commands	79
Creation of New Symbols and Characters	80
Symbol Set	81
International Characters	82
Selecting HP Symbol Sets	82
Barcodes	85
PDF417 Symbol Description	94
Printing a Two-dimensional Barcode	96
Limitations of Two-dimensional Barcode	97
Macro PDF417	98
Creating a Macro PDF 417 Representation	98
Permanent Parameters	101
Interface-dependent Parameters	102
Interface-independent Parameters	105
Emulation	113
Automatic emulation sensing	115
General Information on Emulation	115
Line Printer Emulation (Mode 0)	115
IBM Proprinter X24E Emulation (Mode 1)	116
IBM Proprinter X24E Control Codes	118
IBM Symbol Sets	121
Diablo 630 Emulation (Mode 2)	124
Diablo 630 Control Codes	126
Diablo 630 Symbol Sets	128
Epson LQ-850 Emulation (Mode 5)	133
EPSON LQ-850 Control Codes	136
LQ-850 Symbol Sets	138
HP LaserJet Emulation (Mode 6)	145
LaserJet Fonts	147
LaserJet Symbol Sets	149
Resource Protection	152
Switching the Print Resolution	154
HP LaserJet Reset State	155
LaserJet PJL	155
HP LaserJet Printer Commands - PCL	161
HP-GL/2 Context Printer Commands	177
PJL Syntax Comparison	179
LaserJet Symbol Sets	180
HP 7550A Emulation [KC-GL] (Mode 8)	209
Basic	209
KC-GL Environment Options	210
Plotter Status Information	215
Device-Control Instructions	219
Fonts and Symbol Sets in KC-GL	220
KC-GL Symbol Sets	221
KC-GL Limits	223
Summary of KC-GL Instructions	224
KPDL Operators	228
Communication with the Printing System	228
KPDL Summary	229
KPDL Error Messages	252
KPDL Printable Area	253
Index	255
Numerics	255
A	255
B	255
C	255
D	255
E	255
F	256
G	256
H	256
I	256
K	256
L	256
M	256
N	256
O	257
P	257
Q	257
R	257
S	257
T	257
U	257
W	257
X	257

Match case Limit results 1 per page

HP LaserJet Emulation (Mode 6)

7-33

HP LaserJet Emulation (Mode 6)

On shipment from the factory, the printing system is set to power up in the HP LaserJet

(PCL 6) emulation.

The factory default symbol set is PC-8. To change this default symbol set, use the FRPO

command with the U6 and U7 parameters. The default font is Courier.

To set the printing system to power up in LaserJet mode, send the following PRE-

SCRIBE command:

!R! FRPO P1, 6; FRPO P3, 1; EXIT;

To use the TimesNewRoman font of 14.25 points as the default font, add the following

lines:

FRPO V3, ’TimesNewRoman’;

FRPO V1, 14;

FRPO V2, 25;

See

Chapter 6

for details of the FRPO V parameters.

The symbol set can be changed after power-up with the CSET or INTL command, or

from the operator panel keys, or with LaserJet symbol sets typically accessed through

software.

The printing system also supports as many HP symbol sets as the LaserJet regularly sup-

ports and still other symbol sets can be provided in downloaded fonts. (A full list of the

supported symbol sets appear in section

LaserJet Symbol Sets

on page 37.) These symbol

sets can be used by appropriate font selection commands as explained below.

Fonts can be selected with PRESCRIBE commands, or through the printer driver pro-

vided with your software. The following font sample was created through driver support.