Kyocera TASKalfa 7550ci Kyocera Command Center RX User Guide Rev-1.2 - Page 29

Unusable Time Setting when FAX is installed, Entry Check for New Destination

Get Kyocera TASKalfa 7550ci PDF manuals and user guides View all Kyocera TASKalfa 7550ci manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Settings Pages Specifies the time from 1 to 240 minutes after which the system enters the low power mode, where it reduces the power consumption. Interrupt Clear Time This determines the time of period before the machine reverts to normal mode, after the interrupt copy mode has been engaged. The range is 5 to 459 seconds (in 5-second increments). WSD Scan Timer This determines the time of period before the machine reverts to normal mode, after WSD scan mode has been engaged. The range is 10 to 495 seconds (in 5-second increments). File Name You can change the file name for the scan data or the job name for the jobs on the Job page. Additional Information You can add a Job Number or the Data and Time to the File Name designated above. The additional information varies depending on model. Skip Error Job Turns Skip Error Job on and off, which automatically terminates processing a job on an error and skips to process the next job. The time of period (interval) for the system to wait until the job is skipped can be set by Set Interval below. Set Interval Selects the time of period until Skip Error Job is activated from 5 to 90 seconds. MP Tray Empty With the MP tray set as the default paper source, this enables (On) or disables (Off) the paper empty message when the MP tray becomes empty. Unusable Time Setting (when FAX is installed) This restricts use of the machine by time of day. When turned On, the machine becomes inoperative during the time of day specified by Unusable Time. Except, the received faxes are stored in the machine and printed after the inoperative time period has been expired. Unusable Time This determines the time of period during which the machine is restricted for use. This is enabled when Unusable Time Setting is On. Unlock Code Entering this code, comprised of four digits from 0 to 9, temporarily allows the machine to be usable during the time of period of restriction. Dest(ination) Check Before Send This enables the front panel message which prompts you to confirm the destination to forward the scan data. The message is displayed when the machine's Start key is pressed to start scanning. Entry Check for New Dest(ination) When enabled, this determines whether re-entry of a password for confirmation is required when adding a new destination. Default Screen (Send/FAX) You can select either Destinations or Address Book to be displayed by default on the print system's display while using send or FAX mode. COMMAND CENTER RX 6-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Settings Pages
Specifies the time from 1 to 240 minutes after which the system enters the
low power mode, where it reduces the power consumption.
Interrupt Clear Time
This determines the time of period before the machine reverts to normal
mode, after the interrupt copy mode has been engaged. The range is 5 to
459 seconds (in 5-second increments).
WSD Scan Timer
This determines the time of period before the machine reverts to normal
mode, after WSD scan mode has been engaged. The range is 10 to 495
seconds (in 5-second increments).
File Name
You can change the file name for the scan data or the job name for the jobs
on the Job page.
Additional Information
You can add a Job Number or the Data and Time to the File Name
designated above. The additional information varies depending on model.
Skip Error Job
Turns Skip Error Job on and off, which automatically terminates processing a
job on an error and skips to process the next job. The time of period (interval)
for the system to wait until the job is skipped can be set by
Set Interval
below.
Set Interval
Selects the time of period until Skip Error Job is activated from 5 to 90
seconds.
MP Tray Empty
With the MP tray set as the default paper source, this enables (
On
) or
disables (
Off
) the paper empty message when the MP tray becomes empty.
Unusable Time Setting (when FAX is installed)
This restricts use of the machine by time of day. When turned
On
, the
machine becomes inoperative during the time of day specified by
Unusable
Time
. Except, the received faxes are stored in the machine and printed after
the inoperative time period has been expired.
Unusable Time
This determines the time of period during which the machine is restricted for
use. This is enabled when
Unusable Time Setting
is
On
.
Unlock Code
Entering this code, comprised of four digits from 0 to 9, temporarily allows
the machine to be usable during the time of period of restriction.
Dest(ination) Check Before Send
This enables the front panel message which prompts you to confirm the
destination to forward the scan data. The message is displayed when the
machine's Start key is pressed to start scanning.
Entry Check for New Dest(ination)
When enabled, this determines whether re-entry of a password for
confirmation is required when adding a new destination.
Default Screen (Send/FAX)
You can select either
Destinations
or
Address Book
to be displayed by
default on the print system's display while using send or FAX mode.
COMMAND CENTER RX
6-7