LG LRFDS3016S Owners Manual - Page 19

Assembling the Left Refrigerator

Get LG LRFDS3016S PDF manuals and user guides View all LG LRFDS3016S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

INSTALLATION 19 ENGLISH NOTE • The number of wire harnesses may vary depending on the model. • Ground wire is only present on some models. 4 Push the water supply lines into the hole on the top case and pull them through the backplate. Assembling the Left Refrigerator Door CAUTION • Install the left refrigerator door after the right door is installed. 1 Make sure that the plastic sleeve is inserted in the bottom of the door. Install the refrigerator door onto the middle hinge. 5 Hold the water supply connection and gently push in the collet d to connect the water supply lines as shown. Insert the tube at least 5/8 inch (15 mm) into the connector. Insert the clip on the joint to fasten the tubes in place. NOTE • Disassembling/Assembling the Water Lines 2 Fit the hinge a over the hinge lever latch b and slot it into place. Rotate the lever c clockwise and fasten the hinge. e Collet f Tube g Insert line h Clip • Gently press the collet and insert the tube until only one line shows on the tube. 3 Connect all the wire harnesses and the ground wire.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
19
INSTALLATION
ENGLISH
NOTE
´
The number of wire harnesses may vary
depending on the model.
´
Ground wire is only present on some models.
Assembling the Left Refrigerator
Door
CAUTION
´
Install the left refrigerator door after the right
door is installed.
1
Make sure that the plastic sleeve is inserted in
the bottom of the door. Install the refrigerator
door onto the middle hinge.
2
Fit the hinge
a
over the hinge lever latch
b
and slot it into place. Rotate the lever
c
clockwise and fasten the hinge.
3
Connect all the wire harnesses and the
ground wire.
4
Push the water supply lines into the hole on
the top case and pull them through the
backplate.
5
Hold the water supply connection and gently
push in the collet
d
to connect the water
supply lines as shown. Insert the tube at least
5/8 inch (15 mm) into the connector. Insert
the clip on the joint to fasten the tubes in
place.
NOTE
´
Disassembling/Assembling the Water Lines
e
Collet
f
Tube
g
Insert line
h
Clip
´
Gently press the collet and insert the tube until
only one line shows on the tube.