LG LT1230HR Owners Manual - Page 19

Remote control

Get LG LT1230HR PDF manuals and user guides View all LG LT1230HR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

ENGLISH Operating Instructions Remote control The remote control and control panel will look like one of the following pictures. POWER • To turn the air conditioner ON, push this button. To turn the air conditioner OFF, push the button again. • This button takes priority over any other button. Power TEMPERATURE SETTING • Use this button to automatically control the temperature of the room. The temperature can be set within a range of 60°F to 86°F by increments of 1°F. • The setting appears in the display. FAN SPEED • Every time you push this button it advances the setting as follows: {High[ F2 ] ¡ Low[ F1 ] ¡ High[ F2 ]} Temp Fan Speed Timer Mode TIMER - SHUT-OFF TIME • You will usually use shut-off time while you sleep. • If unit is running, use Timer to set number of hours until shut-off. • For your sleeping comfort, once Time is set, the Temperature setting will raise 2°F after 30 min, and once again after another 30 min. • Push Timer button to advance setting from 1Hour ¡ 2Hours ¡ ... ¡ 12Hours maximum. - START TIME • If unit is off, use Timer to set of hours before unit starts. • Push Timer button to advance setting from 1Hour ¡ 2Hours ¡ ... ¡ 12Hours maximum. MODE - Push this button to shift mode of operation from COOL ¡ ENERGY SAVER ¡ FAN ¡ Heat. - COOL: • Fan runs continually for normal cooling operation. - ENERGY SAVER: • The fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on and the unit will check the room air temperature to determine if cooling is needed. - FAN: • Fan-only operation. - HEAT: • Fan runs continually for normal heating operation. When the air conditioner has been performed its cooling or heating operation and is turned off or set to the fan position, wait at least 3 minutes before resetting to the cooling operation again. A slight heat odor may come from the unit when first switching to HEAT after the cooling season is over. This odor, caused by fine dust particles on the heater, will disappear quickly. This is harmless. Owner's Manual 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Owner’s Manual
19
ENGLISH
Operating Instructions
Remote control
The remote control and control panel will look like one of the following pictures.
Power
Temp
Fan Speed
Timer
Mode
POWER
• To turn the air conditioner ON, push this button.
To turn the air conditioner OFF, push the button again.
• This button takes priority over any other button.
TEMPERATURE SETTING
• Use this button to automatically control the temperature of the room.
The temperature can be set within a range of 60
°
F to 86
°
F by
increments of 1
°
F.
• The setting appears in the display.
FAN SPEED
• Every time you push this button it advances the setting as follows:
{High[ F2 ]
→
Low[ F1 ]
→
High[ F2 ]}
TIMER
- SHUT-OFF TIME
• You will usually use shut-off time while you sleep.
• If unit is running, use Timer to set number of hours until shut-off.
• For your sleeping comfort, once Time is set, the Temperature setting will
raise 2
°
F after 30 min, and once again after another 30 min.
• Push Timer button to advance setting from 1Hour
→
2Hours
→
...
→
12Hours maximum.
- START TIME
• If unit is off, use Timer to set of hours before unit starts.
• Push Timer button to advance setting from 1Hour
→
2Hours
→
...
→
12Hours maximum.
MODE
- Push this button to shift mode of operation from COOL
→
ENERGY SAVER
→
FAN
→
Heat.
- COOL:
• Fan runs continually for normal cooling operation.
- ENERGY SAVER:
• The fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on
and the unit will check the room air temperature to determine if cooling is needed.
- FAN:
• Fan-only operation.
- HEAT:
• Fan runs continually for normal heating operation.
When the air conditioner has been performed its
cooling or heating operation and is turned off or
set to the fan position, wait at least 3 minutes
before resetting to the cooling operation again.
A slight heat odor may come from the unit
when first switching to HEAT after the
cooling season is over.This odor, caused
by fine dust particles on the heater, will
disappear quickly. This is harmless.