Lasko S20620 User Manual - Page 4
Model S20620
View all Lasko S20620 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
MODEL S20620 Pin Groove Figure 8A 4. To secure Blade, screw Spinner onto Shaft Counter Clockwise until tight on Blade hub. Timer Button Figure 9 5. With fan head in upright position, align Ornament of Front Grill so it is horizontal and right side up. By starting with the top of the grill and working down, snap Grill in place. NO GRILL CLIPS ARE NEEDED FOR ASSEMBLY. OPERATION This Fan may be operated by the Manual Controls located on front of the unit (as shown in Figure 9) or by the Remote Control (shown in Figure 12). 1. Plug the cord set into a 120 V outlet. 2. Place the Fan on a firm and level surface. Up: Stationary Be sure that the plug fits tightly into outlet. When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater. 3. Apply power to the Fan by pushing the Power Button ( ). 4. FAN SPEED: You may now adjust the fan speed to the desired level by pressing the Fan Speed Button ( ). 5. OSCILLATION: Push down oscillation knob on motor housing to make fan head move from side to side. (Figures 10 and 11) 6. TIMER FUNCTION: This fan is equipped with a timer. The timer can be set for 7 hours. Continue pressing the Timer Button ( ) to reach the desired time setting. To cancel timer, press Timer Button ( ) until lights are extinguished. 7. After turning the Fan off, unplug the unit from the electrical outlet. Figure 10 Rev. A 1/18 4 Power Button Speed Button PASO 1: ARMADO DE LA TUBERÍA 1. Saque el conjunto de la tubería del cartón como muestra. (Figura 1) 2. Desafloje la Tuerca de Ajuste de Altura, girando en sentido contrahorario. (Figura 2) 3. Eleve la Extensión De La Tubería. (Figura 3) 4. Apriete la Tuerca de Ajuste de Altura, girando en sentido horario. (Figura 4) Figura 1 Tubería de Extension Figura 2 Tuerca de Ajuste de Altura Figura 3 Figura 4 No tome tubos separados. En caso de tuberías se separados, insertar un tubo en el tubo B. B A PASO 3: CONJUNTO DE LA CABEZA Conjunto de Cabezal 1. Coloque el Conjunto de Cabezal con el Collar en el Tubo de Extensión. (Figura 6) 2. Sostenga firmemente el Tubo de Extensión y empuje el Conjunto de Cabezal hacia abajo con un movimiento giratorio hasta que quede asentado en el Tubo de Extensión. Collar Tubo de Extensión Figura 6 PRECAUCIÓN: Cuando realice el ajuste de la altura después de conectar el ensamblaje superior, SIEMPRE sostenga el tubo de extensión con una mano, pues al aflojar la tuerca de ajuste de la altura puede causar la caída libre del tubo de extensión y el ensamblaje superior. Down: Oscillate Figure 11 PASO 2: ENSAMBLE DEL PIE COLOQUE LA BASE EN EL PISO 1. Con un movimiento rápido, inserte el extremo de la tubería de gran diámetro en el agujero en la base. (Figura 5) En cuanto la tubería mientras se empuja asegurará la tubería esté completamente asentado en la base. 2. Para ajustar la altura: a) Afloje la Tuerca de Ajuste de Altura. b) Eleve o baje el Tubo de Extensión hasta obtener la altura deseada. c) Apriete la Tuerca de Ajuste de Altura. Tubo de Extensión Tuerca de Ajuste de Altura PASO 4: ENSAMBLE DEL ASPAY REJILLA 1. Inclinarla Cabeza del Ventilador hacia atrás. Coloque la Rejilla Trasera en el Motor. (Figura 7) 2. Alinear la lengüeta de la Rejilla Trasera con la ranura en la parte superior de la cubierta delantera del Motor. Rejilla Trasera Motor Figura 7 3. Asiente la Parrilla Trasera y sujetela con la Tuerca de Plástico hacia la Derecha. Deslice la Helice en el Eje del Motor. (Figura 8) Alinear la Ranura Del Cubo de la tapa con el Pasador del eje del motor. (Figura 8A) Parrilla Trasera Helice Parrilla Delantera Figura 5 Base 2084861 Rev. A 1/18 Figura 8 9 Tuerca de Plastico Tapa de Ventilador 2084861