Lenovo PC 300PL Technical Information Manual 6275, 6285 - Page 12

Terminology Usage, For example, 1 KB equals

Get Lenovo PC 300PL PDF manuals and user guides View all Lenovo PC 300PL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Terminology Usage Attention! The term reserved describes certain signals, bits, and registers that should not be changed. Use of reserved areas can cause compatibility problems, loss of data, or permanent damage to the hardware. When the contents of a register are changed, the state of the reserved bits must be preserved. When possible, read the register first and change only the bits that must be changed. In this manual, some signals are represented in a small, all-capital-letter format (-ACK). A minus sign in front of the signal indicates that the signal is active low. No sign in front of the signal indicates that the signal is active high. The use of the term hex indicates a hexadecimal number. Also, when numerical modifiers such as "K", "M" and "G" are used, they typically indicate powers of 2, not powers of 10. For example, 1 KB equals 1 024 bytes (2 10), 1 MB equals 1 048 576 bytes (2 20), and 1 GB equals 1 073 741 824 bytes (230). When expressing storage capacity, MB equals 1 000 KB (1 024 000). The value is determined by counting the number of sectors and assuming that every two sectors equals 1 KB. Note: Depending on the operating system and other system requirements, the storage capacity available to the user might vary. x Technical Information Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Terminology Usage
Attention!
The term
reserved
describes certain signals, bits, and registers that should not be changed.
Use of reserved areas can cause compatibility problems, loss of data, or permanent damage to the
hardware.
When the contents of a register are changed, the state of the reserved bits must be preserved.
When possible, read the register first and change only the bits that must be changed.
In this manual, some signals are represented in a small, all-capital-letter format (
-ACK
).
A minus sign in
front of the signal indicates that the signal is active low.
No sign in front of the signal indicates that the
signal is active high.
The use of the term
hex
indicates a hexadecimal number.
Also, when numerical modifiers such as “K”,
“M” and “G“ are used, they typically indicate powers of 2, not powers of 10.
For example, 1 KB equals
1 024 bytes (2
10
), 1 MB equals 1 048 576 bytes (2
20
), and 1 GB equals 1073741824 bytes (2
30
).
When expressing storage capacity, MB equals 1 000 KB (1 024 000).
The value is determined by counting
the number of sectors and assuming that every two sectors equals 1 KB.
Note:
Depending on the operating system and other system requirements, the storage capacity available
to the user might vary.
x
Technical Information Manual