Lexmark X945e Clearing Jams Guide

Lexmark X945e Manual

Get Lexmark X945e PDF manuals and user guides View all Lexmark X945e manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark X945e manual content summary:

  • Lexmark X945e | Clearing Jams Guide - Page 1
    F (Horizontal Transport Unit) Door G Door H ADF cover 1 Remove all paper from the multipurpose feeder. 2 Flex and stack the paper. 3 Reload the multipurpose feeder. 4 Adjust the paper guide. Open Cover F, and then remove the jam. Open Door G, and then remove the jam. For staple jams, remove the
  • Lexmark X945e | Clearing Jams Guide - Page 2
    CAUTION-HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot component, allow the surface to cool before touching it. 4 Close Door A. 2 Lift the green lever, and then pull the paper up and toward you. 2 Lift the green lever, and then pull the paper up
  • Lexmark X945e | Clearing Jams Guide - Page 3
    : Make sure all paper fragments are removed. 3 Close Door C. 4 Open Tray 1, and then remove any crumpled paper from the tray. 242-244 paper jams 1 Open Door D. 5 Close the tray. 6 Touch Continue. 3 2 Pull the paper down and away from the printer. Note: Make sure all paper fragments are removed
  • Lexmark X945e | Clearing Jams Guide - Page 4
    fan them. Do not fold or crease the paper. Straighten the edges on a level surface. 3 Load the paper into the multipurpose feeder. 4 Slide the paper guide toward the inside of the tray until it lightly rests against the edge of the paper. d Close Tray 3. g Close the inside cover, and then close
  • Lexmark X945e | Clearing Jams Guide - Page 5
    the paper jam on the right is difficult to remove, rotate the knob clockwise. 3 Close Cover F. 4 Touch Continue. Covers, knobs, and handles located behind finisher Door G Cover, knob, or handle name 1 Cover G1 2 Cover G2 3 Knob G3 4 Cover G4 5 Cover G7 6 Knob G8 7 Handle G9 5 2 Lift both Cover G1
  • Lexmark X945e | Clearing Jams Guide - Page 6
    Knob G8 clockwise, and then remove the jammed paper. 2 Remove the jammed paper. 8 Close Door G. 9 Touch Continue. 284-286 paper jams 1 Open Door H. 3 Close Door H. 4 Touch Continue. 289 staple jam 1 Open Door G. 2 Slide the G5 stapler toward the front of the finisher. 3 Lift the lever, and
  • Lexmark X945e | Clearing Jams Guide - Page 7
    4 Open the staple cover. 6 Place the staple cartridge into the upper stapler. 8 Remove the staple cartridge identified on the display. 5 Remove the jammed staple, and then close the cover. 7 Open the lower staple drawer. 9 Remove the jammed staples, and then place the staple cartridge into the
  • Lexmark X945e | Clearing Jams Guide - Page 8
    10 Close the staple drawer. 5 Open the scanner cover, and then remove any jammed pages. 11 Close Door G. 12 Touch Continue. 290-295 paper jams 1 Remove all original documents from the ADF. be remove easily, rotate the paper advance wheel to the left. 8 6 Close the scanner cover. 7 Touch Continue.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Lexmark™ X94x
Clearing Jams Guide
Clearing jams
Avoiding jams
The following hints can help you avoid jams:
•
Use only recommended paper or specialty media.
For more information, see the
Card Stock & Label Guide
available on the Lexmark Web site at
www.lexmark.com/publications
.
•
Do not load too much paper. Make sure the stack height does
not exceed the indicated maximum height.
•
Do not load wrinkled, creased, damp, or curled paper.
•
Flex, fan, and straighten paper before loading it.
•
Do not use paper that has been cut or trimmed by hand.
•
Do not mix paper sizes, weights, or types in the same stack.
•
Store the paper in an appropriate environment.
•
Do not remove trays while the printer is printing. Wait for
Load
tray <x>
or
Ready
to appear before removing a tray.
•
Do not load the manual feeder while the printer is printing.
Wait for
Load Manual feeder with <x>
to appear.
•
Push all trays in firmly after loading paper.
•
Make sure the guides in the trays are properly positioned, and
are not pressing too tightly against the paper.
•
Make sure all paper sizes and paper types are set correctly in
the control panel menu.
•
Make sure all printer cables are attached correctly. For more
information, see the setup documentation.
Understanding jam numbers
and locations
When a jam occurs, a message indicating the jam location appears.
The following illustration and table list the paper jams that can
occur and the location of each jam. Open doors and covers, and
remove trays to access jam locations.
Jam
numbers
Area name
Instructions
1
200–203
Door A
Open Door A, and then
remove the jam.
2
230–231
Door B
Open Doors A and B,
and then remove any
jams.
3
241
Door C
Open Door C, and then
remove the jam.
Open Tray 1, and then
remove any jams.
4
242–244
Door D
Open Door D, and
then remove the jam.
Open Trays 2–4, and
then remove any jams.
Jam
numbers
Area name
Instructions
5
250
Multipurpose
feeder
1
Remove all paper
from the
multipurpose
feeder.
2
Flex and stack the
paper.
3
Reload the
multipurpose
feeder.
4
Adjust the paper
guide.
6
280–282
Cover F
(Horizontal
Transport Unit)
Open Cover F, and
then remove the jam.
7
283–284
287–288
289
Door G
Open Door G, and
then remove the jam.
For staple jams,
remove the paper
from the accumulator.
Remove the staple
cartridge, and then
clear the staple jam.
8
284–286
Door H
Open Door H, and
then remove the jam.
Door H is located
between the finisher
output bins.
9
290–295
ADF cover
Open the ADF cover,
and then remove the
jam.
200–203 paper jams
1
Open Door A by lifting the release latch and lowering the door.
CAUTION—HOT SURFACE:
The inside of the printer
might be hot. To reduce the risk of injury from a hot
component, allow the surface to cool before touching.
1