LiftMaster H J-Quick Start Guide for L3 Manual - Page 2

" Board Selector Dial Factory Setting is C2 CONTROL WIRING 16 AWG Minimum USE COPPER WIRE ONLY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LiftMaster CPS Thru-Beam Photo Eyes imarm Lirklaustee NfkM .ter T TS CI) CD C, C) lmc-o) _ • -= c#) • z\ CD o m m CS %.< (0 CD CD CI) \ c.) a0 a -cp •D• =© cp 0 E2 / z FSTS DIAG aCD) 9 Blue Brown NEVER run Control wiring in same conduit as the Power wiring! C2 B2 /(? PROG 8 Maintenance Alert LED AFollow ALL local electrical codes 0 0 FAILSAFE B2 C2 D1 E2 ON-FAILSAFE Push and Release to Open (without Mid Stop programming) 0 0 Mid Stop - Programmable Open Override - Available When Photo Eyes or Edge Sensor are triggered, the Door will Reverse and Fully Open. Push and Holdto Close Push and Release to Stop 0 0 1 MAS Programming (Maintenance Alert System) 1. The MAS assists the installing dealer in setting up a routine maintenance program. Once programmed, the MAS notifies the end user (with a flashing LED on the 3 button station) when a preset number of cycles/months has elapsed and scheduled maintenance is due. 6. Press the OPEN button once for every 5,000 Cycles increments. Press the CLOSE button once for every 3 Month increments. Press the STOP button once to Clear the MAS Memory. OPEN D20 CLOSE D21 l'•:1 STOP D13 l'•:1 2. Close the Door. 3. Turn the selector dial to Program. T TS ,FSTS Dl.. C2 'PROG MAS 7. Press the MAS SET button to SET complete the programming. OPE The OPEN LED will flash • once for every 5,000 Cycles. CLOS • The CLOSE LED will flash once for every 3 Months. MAS 4. Press and release the MAS SET button. SET OPEN 120 5. Press the STOP button once CLOSE ( /21 to clear the MAS counter. D13 8. Turn the selector dial back to the desired wiring type. T TS E2\ ,. FSTS C2- B2/ PROG r Timer to Close Programming Timer automatically closes door after a preset time. 1. Close the Door. E2 2. Turn selector to Program. 01, C2 3. Press the TIMER button. MRT MID TIMER 41L14 SET TS ,FSTS PR 4. Press the STOP button to Zero the Timer. OPEN C STOP D13 5. Press the OPEN button once for every 5 seconds. Press the CLOSE button once for every 60 seconds. Example: Push CLOSE + Push OPEN + Push OPEN = 70 seconds total (60 seconds) (5 seconds) (5 seconds) OPEN D20 CLOSE D21 STOP D13 O 6. Press the TIMER button to complete programming. MRT MI TIMER The OPEN LED will flash once for every 5 sec. SET The CLOSE LED will flash once for every 60 sec. 7. Turn selector to T, TS or FSTS wiring types. NOTE: Photo eyes required to enable feature. S E2\ T T/ FS 01. ~OIAG C2 PROG OPE CLOS Li% 01-32524B ©2005, The Chamberlain Group Inc. All Rights Reserved 4 to 6 Inches Edge Sensor Mid Stop Programming The mid stop feature is to open the door to a preset point prior to the fully open position. 1. Close the Door. E2\ 2. Turn selector to Program. C2 3. Press the MID SET button. MRT MID TIMER l;!,1 TS ,. FSTS --DIAG PR OPEN D20 FAQ 4. Press the OPEN button and let door open until it reaches CLOSE D21 the desired Mid Stop height, then press the STOP button. STOP D13 5. Press the MID SET button to set desired height. MRT MID TIMER 6. Turn selector back to selected wiring type. TS E2 ,FSTS --DIAG C2 h