Linksys WRT100 User Guide - Page 10

Router IP, DHCP Server Setting, DHCP Reservation, Clients Already Reserved - ip address

Get Linksys WRT100 - RangePlus Wireless Router PDF manuals and user guides
UPC - 745883581894
View all Linksys WRT100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Chapter 3 Router IP This presents both the Router's IP Address and Subnet Mask as seen by your network. Advanced Configuration Router IP DHCP Server Setting The settings allow you to configure the Router's Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Router's DHCP server option, make sure there is no other DHCP server on your network. DHCP Server Setting DHCP Server DHCP is enabled by factory default. If you already have a DHCP server on your network, or you don't want a DHCP server, then select Disabled (no other DHCP features will be available). DHCP Reservation Click this button if you want to assign a fixed local IP address to a MAC address. DHCP Reservation You will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and MAC Address. RangePlus Wireless Router DHCP Reservation • Select Clients from DHCP Table Click the Select check box to reserve a client's IP address. Then click Add Clients. • Manually Adding Client To manually assign an IP address, enter the client's name in the Enter Client Name field. Enter the IP address you want it to have in the Assign IP Address field. Enter its MAC address in the To This MAC Address field. Then click Add. Clients Already Reserved A list of DHCP clients and their fixed local IP addresses will be displayed at the bottom of the screen. If you want to remove a client from this list, click Remove. Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. To view the most up-to-date information, click Refresh. To exit this screen, click Close. Start IP Address Enter a value for the DHCP server to start with when issuing IP addresses. Because the Router's default IP address is 192.168.1.1, the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.253. The default Starting IP Address is 192.168.1.100. Maximum Number of Users Enter the maximum number of PCs that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253. The default is 50. IP Address Range Displayed here is the range of available IP addresses. Client Lease Time The Client Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be "leased" this dynamic IP address. After the time is up, the user will 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
Chapter±3
Advanced Configuration
6
RangePlus W±reless Router
Router IP
This presents both the Router’s IP Address and Subnet
Mask as seen by your network.
Router IP
DHCP Server Setting
The settings allow you to configure the Router’s Dynamic
Host Configuration Protocol (DHCP) server function. The
Router can be used as a DHCP server for your network. A
DHCP server automatically assigns an IP address to each
computer on your network. If you choose to enable the
Router’s DHCP server option, make sure there is no other
DHCP server on your network.
DHCP Server Setting
DHCP Server
DHCP is enabled by factory default. If you
already have a DHCP server on your network, or you don’t
want a DHCP server, then select
D±sabled
(no other DHCP
features will be available).
DHCP Reservat±on
Click this button if you want to assign
a fixed local IP address to a MAC address.
DHCP Reservation
You will see a list of DHCP clients with the following
information: Client Name, Interface, IP Address, and
MAC Address.
DHCP Reservation
Select Cl±ents from DHCP Table
Click the
Select
check box to reserve a client’s IP address. Then click
Add Cl±ents
.
Manually Add±ng Cl±ent
To manually assign an IP
address, enter the client’s name in the
Enter  Client 
Name
field. Enter the IP address you want it to have in
the
Assign IP Address
field. Enter its MAC address in the
To This MAC Address
field. Then click
Add
.
Clients Already Reserved
A list of DHCP clients and their fixed local IP addresses
will be displayed at the bottom of the screen. If you
want to remove a client from this list, click
Remove
.
Click
Save Sett±ngs
to apply your changes, or click
Cancel Changes
to cancel your changes. To view the
most up-to-date information, click
Refresh
. To exit this
screen, click
Close
.
Start IP Address
Enter a value for the DHCP server to
start with when is
suing IP addresses. Because the Router’s
default IP address is 192.168.1.1, the Start IP Address must
be 192.168.1.2 or greater, but smaller than 192.168.1.253.
The default Starting IP Address is
²92.²68.².²00
.
Max±mum
Number
of
Users
Enter
the
maximum
number of PCs that you want the DHCP server to assign
IP addresses to. This number cannot be greater than 253.
The default is
50
.
IP Address Range
Displayed here is the range of available
IP addresses.
Cl±ent Lease T±me
The Client Lease Time is the amount
of time a network user will be allowed connection to the
Router with their current dynamic IP address. Enter the
amount of time, in minutes, that the user will be “leased”
this dynamic IP address. After the time is up, the user will
•
•