Lowrance HDS-9 Gen3 Installation Manual US - Page 17

Flush mounting

Get Lowrance HDS-9 Gen3 PDF manuals and user guides View all Lowrance HDS-9 Gen3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Flush mounting Check the template for scaling accuracy, using a tape measure or ruler against the ruler printed on the template. Cut away excess paper, and tape down the template. Check that it is correctly aligned to a vertical or horizontal reference. Do not use a bubble level as vessel may be unlevel! Adjust where required. 95.3 mm (7.50") MOUNTING SCREW SIZE IS #6 TAPPING SCREW CL 110.2 mm (3.75") 99.5 mm (3.92") 95.3 mm (7.50") PRODUCSTUNOUCTOLVINEER CL Drill all marked pilot holes, then using an appropriate saw, cut through the template and mounting surface, along the dotted line bordering the shaded center of the template. 190.5 mm (7.50") 199.0 mm (7.83") 220.4 mm (8.68") Check dimensions before cutting 12" Remove the bezel from the display by first opening the card reader door. Using a fingernail or small flat screwdriver, pull off the bezel at the slotted points immediately above and below the card reader. Pull bezel around keypad forward, till hidden tab at top right can be disengaged by a slight downward pull. Applying a slight twist to top bezel edge will disengage the top left hidden tab. The rest of the bezel should come away easily. Check the fit of the display, and use a file to remove any remaining obstructions. If water-tightness is required, apply a thin, continuous bead of sealant to the back of the display prior to final installation. Sealant should be of a 'neutral cure' type to prevent damage to the plastics. Secure the display with the supplied screws. Once screws are fully tightened, ensure there is complete contact with the mounting surface. Lastly, install the bezel with the card reader door open; insert the outermost tabs on the bezel into the slots on the display, then gently press down the bezel above and below the card reader door until it clicks in to place. Display Installation | HDS Gen3 Installation Manual | 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
| 15
Display Installation |
HDS Gen3 Installation Manual
Flush mounting
Check the template for scaling accuracy, using a tape measure or
ruler against the ruler printed on the template.
Cut away excess paper, and tape down
the template. Check that it is correctly
aligned to a vertical or horizontal
reference. Do not use a bubble level as
vessel may be unlevel! Adjust where
required.
Drill all marked pilot holes, then using an
appropriate saw, cut through the
template and mounting surface, along
the dotted line bordering the shaded
center of the template.
Remove the bezel from the display
by first opening the card reader
door. Using a fingernail or small flat
screwdriver, pull off
the bezel at the
slotted points immediately above
and below the card reader. Pull bezel
around keypad forward, till hidden
tab at top right can be disengaged
by a slight downward pull. Applying
a slight twist to top bezel edge will
disengage the top left hidden tab.
The rest of the bezel should come
away easily.
Check the fit of the display, and use a file to remove any remaining
obstructions. If water-tightness is required, apply a thin, continuous
bead of sealant to the back of the display prior to final installation.
Sealant should be of a ‘neutral cure’ type to prevent damage to the
plastics. Secure the display with the supplied screws. Once screws
are fully tightened, ensure there
is complete contact with the
mounting surface. Lastly, install
the bezel with the card reader
door open; insert the outermost
tabs on the bezel into the slots
on the display, then gently press
down the bezel above and
below the card reader door until
it clicks in to place.
L
C
L
C
Check dimensions before cutting
12"