Lowrance HDS-9 Gen3 Installation Manual US - Page 34

Device list

Get Lowrance HDS-9 Gen3 PDF manuals and user guides View all Lowrance HDS-9 Gen3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Configure device Additional device options can be configured from both the Data source menu or from the Device list, see "Device list" on page 32 for further information. Scope The active data source under any given category, can be set to be Global or Local. When a source is set as Global, it will be used by all displays on the network. When a source is set as Local, it will only be used by the display that selected it as the source.  Note: If changing a display from a Global source to a different Local source, change the Scope setting to Local before changing the selected source, otherwise all other displays will be changed over to the new source.  Note: Local and Global data settings apply to the selected data source only. It is not possible to discretely set whether a data source is Global or Local if it is not the active source on the display being operated. Reset Global/Local Selecting Reset Global will run an Auto data source selection, and override all previous manual source selections made on all networked devices. Reset Local will revert all data source selections on the display being used to the Global source settings available from other networked displays. Device list The device list shows the physical and virtual devices that provide data. This may include a module inside the HDS Gen3, the NMEA 0183 port, or any external NMEA 2000 device. Selecting a device in this list will bring up additional details and possible actions: 32 | Software setup | HDS Gen3 Installation Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
32 |
Software setup |
HDS Gen3 Installation Manual
Configure device
Additional device options can be configured from both the Data
source menu or from the Device list, see “Device list” on page 32
for further information.
Scope
The active data source under any given category, can be set to be
Global or Local.
When a source is set as Global, it will be used by all displays on the
network. When a source is set as Local, it will only be used by the
display that selected it as the source.
Note:
If changing a display from a Global source to a different Local
source, change the Scope setting to Local
before
changing the
selected source, otherwise all other displays will be changed over to
the new source.
Note:
Local and Global data settings apply to the selected data
source only. It is not possible to discretely set whether a data source
is Global or Local if it is not the active source on the display being
operated.
Reset Global/Local
Selecting
Reset Global
will run an Auto data source selection,
and override all previous manual source selections made on all
networked devices.
Reset Local
will revert all data source selections
on the display being used to the Global source settings available
from other networked displays.
Device list
The device list shows the physical and virtual devices that provide
data. This may include a module inside the HDS Gen3, the NMEA
0183 port, or any external NMEA 2000 device.
Selecting a device in this list will bring up additional details and
possible actions: