Lowrance StructureScan HD Transom Installation Manual
Lowrance StructureScan HD Manual
 |
View all Lowrance StructureScan HD manuals
Add to My Manuals
Save this manual to your list of manuals |
Lowrance StructureScan HD manual content summary:
- Lowrance StructureScan HD | Transom Installation Manual - Page 1
StructureScan HD Transom mount Installation Guide ENGLISH www.bandg.com | www.simrad-yachting.com | www.lowrance.com - Lowrance StructureScan HD | Transom Installation Manual - Page 2
of transducers and other components of the system are critical to the performance of the system as intended. If in doubt, consult your Navman dealer. To reduce the risk of misusing or misinterpreting this instrument, you must read and understand all aspects of this Installation and Operation Manual - Lowrance StructureScan HD | Transom Installation Manual - Page 3
the accessory. This manual has installation instructions for your accessory, and accessory pack content tables on the back cover. Contents Your StructureScan box is packed with the StructureScan HD module, a Power cable, fuse and fuse holder, StructureScan transducer, mounting bracket, 15 foot (4.5m - Lowrance StructureScan HD | Transom Installation Manual - Page 4
your boat/installation preferences. ¼¼ Note: When mounting the StructureScan transducer, make sure there is nothing around the mounting location that could interfere with StructureScan transducer sonar beams. Jackplate mount Step mount Transom mount 4 | StructureScan HD | Installation preparation - Lowrance StructureScan HD | Transom Installation Manual - Page 5
Protects transducer and prevents drag from transducer (Page 11) Transducer angle can not be adjusted so it is parallel with the water Does not track bottom when boat is on plane Trolling motor mount (sold separately) Visit www.transducershieldandsaver.com StructureScan HD | Installation - Lowrance StructureScan HD | Transom Installation Manual - Page 6
2 Installation Bracket and transducer assembly The StructureScan bracket comes with four washers, two bolts and two nuts. If you plan to mount the StructureScan transducer directly to the step (Step Mount) or on the trolling motor, you do not need to assemble the bracket. OR 6 | StructureScan HD - Lowrance StructureScan HD | Transom Installation Manual - Page 7
transducer and broadband sounder transducer both are installed on the trolling motor. Downscan overlay performance could be degraded if the StructureScan transducer is too far away from the broadband sounder transducer installed on the trolling motor. < 0.3m (1ft) StructureScan HD | Installation - Lowrance StructureScan HD | Transom Installation Manual - Page 8
pilot holes and fasten the bracket to the transom using your drill and the supplied screws. 6. To make adjustments to transducer position, loosen the screws and slide bracket up or down. 7. Connect the transducer cable to the StructureScan module sonar port. 8 | StructureScan HD | Installation - Lowrance StructureScan HD | Transom Installation Manual - Page 9
holes. 10. Place a washer over the end of the bolts and tighten the nuts. 11. Connect the transducer cable to the StructureScan module sonar port. Jackplate StructureScan bracket mounted inside the jackplate. The bracket can also be installed on the outside of the jackplate. StructureScan HD - Lowrance StructureScan HD | Transom Installation Manual - Page 10
holes and fasten the bracket to the transom using your drill and the supplied screws. 7. To make adjustments to transducer position, loosen the screws and slide bracket up or down. 8. Connect the transducer cable to the StructureScan module sonar port. Step 10 | StructureScan HD | Installation - Lowrance StructureScan HD | Transom Installation Manual - Page 11
fiberglass pilot holes or crack the mounting holes on the StructureScan transducer. 7. Connect the transducer cable to the StructureScan module and then turn on the Flip Left/Right feature on your display unit. Direct mount (without bracket) Do not install under boat hull! ¼¼ NOTE: When using - Lowrance StructureScan HD | Transom Installation Manual - Page 12
washers (4) StructureScan Skimmer Transducer (000-10802-001) Transom mount screws (2) Bracket assembly nuts (2) Transducer attachment lock nuts (6) Transducer attachment screws (6) Bracket assembly bolts (2) Zip ties (2) Bracket assembly washers (4) 12 | StructureScan HD | Installation - Lowrance StructureScan HD | Transom Installation Manual - Page 13
Communication Ethernet Shared devices supported 3 Weight StructureScan module (1.8lbs) Transducer (1.9lbs) Transducer with bracket (2.55lbs) Max Range Max Speed Mark objects Optimum speed Sidescan Specifications 455kHz (500ft - 250 per side) 35 mph (56 kmh) 15 mph (24 kmh) 10 mph (16 kmh) or - Lowrance StructureScan HD | Transom Installation Manual - Page 14
Indicator Transducer LED Transducer LED Transducer LED Power LED Power LED Power LED Power LED Power LED Ethernet LED Ethernet LED StructureScan LED Guide LED Status Definition Off Transducer not connected or cable/transducer is broken Green/ stays Transducer detected/locked on to on bottom - Lowrance StructureScan HD | Transom Installation Manual - Page 15
StructureScan Troubleshooting Tips • Make sure StructureScan HD is powered StructureScan not displayed • Check unit software; must have at least version 2.5 • Make sure yellow wire is connected to switched power source • Check fuse No Data Check range or turn on auto range Data washed out/ - Lowrance StructureScan HD | Transom Installation Manual - Page 16
*988-10284-001* www.bandg.com www.simrad-yachting.com www.lowrance.com
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
ENGLISH
StructureScan HD
Transom mount
Installation Guide
www.bandg.com | www.simrad-yachting.com | www.lowrance.com