Magnavox 19MD358B User Manual - Page 11

Power

Get Magnavox 19MD358B - 19inch LCD TV PDF manuals and user guides
UPC - 609585144354
View all Magnavox 19MD358B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

ENGLISH FRANÇAISE ESPAÑOL 4.4 Connect the AC power cord Cable Receiver Box BB WARNING: Verify that your voltage corresponds with the voltage printed at the back of the TV. Do not insert the AC power cord if the voltage is different. To connect the AC power cord 4.6 Switch on the TV Before you switch on the TV, check that the mains cord is properly connected. Press POWER button at the front side of the TV, or press power the remote control. The TV normally takes 10-15 seconds to start up and the following screen appears the first time you turn on the TV. Thank you for your purchase TV. Please proceed with the following steps to set-up your TV. For the BEST possible picture performance, contact your local Cable / Satellite signal provider for High Definition signal options available in your area. 1. Locate the power connector at the back of the TV. The location of the power connector varies according to TV model. 2. Insert the AC power cord fully into the TV power connector. 3. Connect the AC power cord plug to the power outlet. Ensuring that the cord is tightly secured at both ends. Next Press the GREEN Next button on your remote to proceed. Follow the on-screen instructions to select your language and complete your TV setup. Installation takeThsankaypoupforroyoxuripmurcahatsee ly 10 TmV. inutes. Please proceed with the following steps to set-up your TV. For the BEST possible picture performance, contact your local Cable / Satellite signal provider for High Definition signal options available in your area. DD Note: If you connect your TV to a cable receiver box or satellite set-top box, you do not need to install channels. Press the red button on the Next remote control to exit the Press the GREEN Next button on your remote to proceed. channel installation stage of the setup. 4.5 Manage cables Route your AC power cord, antenna cable and all other device cables through the cable holder at the back of the TV. The holder helps keep your cables tidy and easily manageable. 75 Ω EN-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
EN-10
ENGLISH
FRANÇAISE
ESPAÑOL
Connect the AC power cord
4.4
WARNING
B
:
Verify that your voltage corresponds with
the voltage printed at the back of the TV.
Do not insert the AC power cord if the
voltage is different.
To connect the AC power cord
Locate the power connector at the back of the
1.
TV.
The location of the power connector varies
according to TV model.
Insert the AC power cord fully into the TV
2.
power connector.
Connect the AC power cord plug to the power
3.
outlet. Ensuring that the cord is tightly secured
at both ends.
4.5
Manage cables
Route your AC power cord, antenna cable and all
other device cables through the cable holder at the
back of the TV. The holder helps keep your cables
tidy and easily manageable.
Switch on the TV
4.6
Before you switch on the TV, check that the mains
cord is properly connected.
Press
POWER
button at the front side of the TV, or press power
the remote control.
The TV normally takes 10-15
seconds to start up and the following screen appears
the first time you turn on the TV.
Thank you for your purchase
TV.
Please proceed with the following steps to set-up your TV. For the BEST
possible picture performance, contact your local Cable / Satellite signal
provider for High Definition signal options available in your area.
Next
Press the GREEN Next button on your remote to proceed.
Follow the on-screen instructions to select your
language and complete your TV setup.
Installation
takes approximately 10 minutes.
Note:
D
If you connect your TV to a cable receiver
box or satellite set-top box, you do not need
to install channels.
Press the red button on the
remote control to exit the channel installation
stage of the setup.