Magnavox 27MS3404 User manual, English (US) - Page 8

Cable Box w/RF, In/Outputs, Cable Box w/Audio/Video, Outputs - remote

Get Magnavox 27MS3404 - Stereo Tv PDF manuals and user guides View all Magnavox 27MS3404 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

BASIC CABLE BOX/DECODER CONNECTION If your cable signal uses a cable box or decoder, follow the easy steps below to complete the connection. Cable Box Connection (RF Input/Output Only): Cable Box (w/RF In/Outputs): This connection will NOT supply Stereo sound to the TV. The sound from the cable box will be mono. Cable Signal IN from the Cable 1 Company Jack Panel Back of Cable Box 2 OUTPUT CH 1 Connect the open end of the round Cable Company supplied cable to the cable signal IN(put) plug on the back of the Cable Box. CABLE IN TO TV 3 4 2 Using a separate round coaxial cable, connect one end to the OUT(put) (TO TV) plug on the back of the Cable Box. Round 75Ω Coaxial Cable 3 3 Connect the other end of the round coaxial cable to the 75Ω input on the back of the television. Screw it down finger tight. NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the back of the cable box to CH 3 or 4, then tune the TV to the corresponding channel. Once tuned, change channels at the cable box, not the television. Cable Box (w/Audio/Video Outputs): This connection will supply Stereo sound to the TV. 4 Connect the open end of the round Cable Company supplied cable to the cable signal IN(put) plug on the back of the Cable Box. 5 Using a RCA type Video Cable, connect one end of the cable to the Video (or ANT, your cable box may be labeled differently) Out jack on the cable box and the other end to the AV1 Video Input on the TV. 6 Using a RCA type Audio Left and Right Cable, connect one end to the left and right Audio Out L & R jacks on the cable box. Connect the other end to the AV1 Audio L & R Input jacks on the TV. ANT 75‰ Monitor out AV1 in VIDEO Y L/Mono AUDIO Pb AV2 in R Pr COMPONENT VIDEO INPUT S-VIDEO Jack Panel Back of TV Cable Box Connection (with Audio/Video Outputs): Cable Signal IN from the Cable Company 4 CABLE IN OUTPUT CH 3 4 TO TV Jack Panel Back of Cable Box VIDEO OUT L R AUDIO OUT Cable Box with Audio/Video Outputs 24 RCA type Video Cable 5 RCA type Audio Left and Right Cables Monitor out AV1 in VIDEO Y L/Mono AUDIO Pb AV2 in R Pr COMPONENT VIDEO INPUT Jack Panel Back of TV S-VIDEO 6 ANT 75‰ Monitor out AV1 in VIDEO Y L/Mono AUDIO Pb AV2 in R Pr COMPONENT VIDEO INPUT S-VIDEO NOTE: Use the Channel + or - buttons on the TV remote control to tune to the AV1 channel for the cable box signal. Once tuned, change channels at the cable box, not the television. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
8
CABLE
IN
TO
TV
VIDEO
OUT
L
R
AUDIO
OUT
3
4
OUTPUT
CH
TO TV
CABLE
IN
3
1
2
24
L/Mono
Monitor out
VIDEO
S-VIDEO
AV1 in
Y
Pb
Pr
AV2 in
AUDIO
R
COMPONENT VIDEO INPUT
4
5
6
OUTPUT
CH
3
4
Cable Box Connection (RF Input/Output Only):
Jack Panel Back of Cable Box
Cable Signal
IN from the
Cable
Company
Round 75
Ω
Coaxial Cable
Jack Panel Back of TV
Cable Box Connection (with Audio/Video Outputs):
Cable Signal IN from
the Cable Company
Jack Panel Back
of Cable Box
Cable Box with
Audio/Video Outputs
RCA type Audio
Left and Right
Cables
Jack Panel Back of TV
I
f your cable signal uses a cable box or
decoder, follow the easy steps below to com-
plete the connection.
Cable Box (w/RF
In/Outputs):
This connection will NOT supply Stereo
sound to the TV. The sound from the cable
box will be mono.
1
Connect the open end of the
round Cable Company supplied
cable
to
the cable signal IN(put) plug
on the back of the Cable Box.
2
Using a separate round coaxial cable,
connect one end to the OUT(put)
(TO TV) plug on the back of the
Cable Box.
3
Connect the other end of the
round coaxial cable
to the 75
Ω
input
on the back of the television. Screw it
down finger tight.
NOTE:
Be sure to set the OUTPUT CHAN-
NEL SWITCH on the back of the cable box to
CH 3 or 4, then tune the TV to the corre-
sponding channel. Once tuned, change chan-
nels at the cable box, not the television.
Cable Box (w/Audio/Video
Outputs):
This connection will supply Stereo sound to
the TV.
4
Connect the open end of the
round Cable Company supplied
cable
to
the cable signal IN(put) plug
on the back of the Cable Box.
5
Using a RCA type Video Cable,
con-
nect one end of the cable to the
Video
(or ANT,
your cable box may be
labeled differently
)
Out jack
on the
cable box and the other end to the
AV
1
Video Input on the TV.
6
Using a RCA type Audio Left and Right
Cable,
connect one end to the left
and right Audio Out L & R jacks on
the cable box.
Connect the other end
to the
AV
1
Audio L & R Input jacks on
the TV.
NOTE:
Use the Channel + or – buttons on
the TV remote control to tune to the
AV
1
channel for the cable box signal. Once tuned,
change channels at the cable box, not the tele-
vision.
B
ASIC
C
ABLE
B
OX
/D
ECODER
C
ONNECTION
RCA type Video Cable