Makita LS1016 Technical Reference

Makita LS1016 Manual

Get Makita LS1016 PDF manuals and user guides View all Makita LS1016 manuals
Add to My Manuals
Save this manual to your list of manuals

Makita LS1016 manual content summary:

  • Makita LS1016 | Technical Reference - Page 1
    1 Spare lock-off button 2 Holder set 2 (all countries except North America) Hex wrench 1 (LS1016L only) Note: The standard equipment for the tool shown may differ by country. Optional accessories Horizontal vise TCT saw blades Crown molding stopper set Dust box Portable miter saw stand
  • Makita LS1016 | Technical Reference - Page 2
    (10-1/4") saw blade at 0 degree/ 0 degree Workpiece Crown molding, 45 degree type Baseboard (Skirt board) How to cut Diagonal cut* Horizontal cut Vertical cut Horizontal cut Capacity: mm (") 168** 248 120 305 *Diagonal cut is to cut a crown molding that is held tilted against the guide fence
  • Makita LS1016 | Technical Reference - Page 3
    Flat washer 16 Adjusting Laser beam 134829-3 Socket 17-38 assembly Attachment for 1R254 782232-8 Box wrench 13 (standard accessory) Installing /Removing Blade Adjusting Blade position [2] LUBRICATIONS Apply Lubricants to the designated portions in order to protect parts and product from unusual
  • Makita LS1016 | Technical Reference - Page 4
    LUBRICATIONS (cont.) Apply Makita grease SG.No.00 to the following portions designated with the black triangle to protect parts and product from Center cover contacts 136 143 Lower fence a. Portion where Pin 4 contacts 138 Guide fence b. Portion where Lower fence contacts 63 Blade case 149
  • Makita LS1016 | Technical Reference - Page 5
    with Spur gear 34 228 Miter lock plate Surface where Cam portion of Grip 50 contacts. 242 Base Hole for pivoting of Turn base 248 Slide plate Surface on which 207 Turn base moves Amount 15g a little 8g a little Fig. 5 Motor and Blade case section Motor bracket 14 Blade case Blade
  • Makita LS1016 | Technical Reference - Page 6
    (2pcs.) Fig. 9 Remove Link plate as illustrated below. 1. Remove Stop ring E-5, Flat washer 6 and Ring 6. Link plate complete can be free from blade case. Stop ring E-5 Flat washer 6 Ring 6 Link plate complete 2. Remove M6x20 Hex socket head bolt, Flat washer 6 and Ring 6. Link plate complete
  • Makita LS1016 | Technical Reference - Page 7
    Motor section (cont.) P 7/ 37 DISASSEMBLING (2) Remove Rod 16 as illustrated in Figs. 10 and 11. Blade case can be separated from Arm and Base section. Fig. 10 1. Remove M5x18 Hex socket . Blade case Rod 16 Socket wrench 10 Remove Rod 16 by striking the Socket wrench 10 in the same direction in
  • Makita LS1016 | Technical Reference - Page 8
    14. Fig. 13 1. Remove Carbon brushes from Motor housing. 3. Disconnect connectors of Laser circuit from that of Power supply circuit. Lead cover The electrical parts in Handle can be replaced. 6x18 Tapping screw (6pcs.) Handle section Motor housing Handle cover Motor housing Motor bracket
  • Makita LS1016 | Technical Reference - Page 9
    DISASSEMBLY/ASSEMBLY [3]-1. Blade case, Motor section (cont.) P 9/ Knob 20 toward the notch to keep 90 degrees between Blade case and Base. Knob 20 top end of Rod 16 left hole of Blade case 35 with M6x20 Hex socket head bolt until the Hex socket head bolt is seated on Blade case. And tighten
  • Makita LS1016 | Technical Reference - Page 10
    10/ 37 Handle rib of Blade case Pressing Handle toward the rib of Blade case, assemble it to Motor housing by tightening with 4x18 Tapping screws. Lead cover Lead cover holder Motor Blade case and Bearing box and Blade case together with Bearing box. lift up Bearing box as illustrated M5x16
  • Makita LS1016 | Technical Reference - Page 11
    1R291 from the shaft of Helical gear 14. Flat washer 12 Spiral bevel gear 32 Unscrew 4x12 Tapping screws and remove Grease holder from Bearing box. 4x12 Tapping screw Grease holder Fig. 23 1R045 1R346 Ball bearing 608DDW Ball bearing 608DDW can be removed by pressing from Grease holder side to
  • Makita LS1016 | Technical Reference - Page 12
    Fig. 27 Assemble Helical gear 27, Ball bearing 6000ZZ and Steel ball 4 to Gear shaft. And then, assemble the Helical gear 27 section to Bearing box. Convex side Steel ball 4 Gear shaft Helical gear 28 The convex side has to be faced to Gear shaft end on which Steel ball 4 is
  • Makita LS1016 | Technical Reference - Page 13
    Spiral bevel gear 32 to the shaft of Helical gear 14 as illustrated in Fig. 29. Fig. 28 Pressfit Ball bearing 608DDW to Bearing box. Tighten provisionally Bearing retainer 14-23. Assemble Helical gear 14 with 1R045 and R346. Spindle Helical gear 28 1R045 Helical gear 27 1R346 Ball bearing
  • Makita LS1016 | Technical Reference - Page 14
    S-12 Flat washer 12 Put Bearing box on 1R036. Applying 1R028 to Retaining gear 14. And tighten M5 Hex nut with Socket wrench 8 while pressing Shaft lock. Refer to the Motor housing to Blade case. Refer to the left illustration in Fig. 14 and the left illustration in Fig. 13. (10 Stop ring E-6
  • Makita LS1016 | Technical Reference - Page 15
    position of Lock lever as illustrated in Fig. 33. Fig. 32 P 15/ 37 Insert Rod 8 into Rod holder, and set Rod holder to Blade case. Stop ring E-6 rod 8 While pushing Rod holder toward the rib of Blade case, secure Rod holder with 4x16 Tapping screw (2pcs.). And assemble Torsion spring 8. rib
  • Makita LS1016 | Technical Reference - Page 16
    Repair [3] DISASSEMBLY/ASSEMBLY [3]-4. Safety cover A P 16/ 37 ASSEMBLING (1) Assemble Safety cover A section as illustrated in Fig. 34. And then mount the Safety cover A section to Safety cover B as illustrated in Fig. 35. (2) Mount the Safety cover section to Blade case complete as illustrated
  • Makita LS1016 | Technical Reference - Page 17
    designated with black arrow until it stops. Kerf board 3. Remove Miter scale plate from Base by unscrewing 4x12 Tapping screw (3pcs.) Lower fence (2pcs.) Guide fence Grip 50 Fig. 38 Remove M8x45 Hex bolt with Socket wrench 13. And remove Flat washer 8. Turn base section M8x45 Hex bolt Flat
  • Makita LS1016 | Technical Reference - Page 18
    [3]-6. Positive lock mechanism of Turn base P 18/ 37 DISASSEMBLING Fig. 40 (1) Remove Stop ring E-7. (Fig. 40) Grip 50, Compression spring 11, Flat washer 10 and Cam Stop ring E-7 can be removed. (2) Remove M6x14 H.S.Binding head screw then remove Miter lock plate in the direction designated
  • Makita LS1016 | Technical Reference - Page 19
    base (cont.) ASSEMBLING Note: Assemble Grip 50 to Miter lock plate as illustrated in Fig. 46 Fig. 46 so that the notch of Cam portion faces the upper side. Miter moving range. Then remove M6x20 Hex socket head bolt for securing Link plate. . Note: Apply Makita grease SG No.00 to O ring 5
  • Makita LS1016 | Technical Reference - Page 20
    ) 2) Remove M4x10 Pan head screw and then remove Lever 105. (Fig. 51) 3) Remove M10 Hex bolt and Flat washer 10. (Fig. 51) 4) Remove M10-17 Hex lock nut using Box wrench 17. Flat washer 10 (2pcs.) and Thrust needle cage 1024 can be removed as illustrated in Fig. 52. 5) Remove Arm section from Arm
  • Makita LS1016 | Technical Reference - Page 21
    arrow. (Fig. 57) 10) Attach a thin slotted screwdriver to Stop ring E-4, and strike the head of the screwdriver by hand. (Fig. 58) Stop ring E-4, Cam and Lever 1R254, 1R220, 1R222 and Socket assembly 17-38. When Lever 105 is set in place and Handle is held by hand, Motor section has to be smoothly
  • Makita LS1016 | Technical Reference - Page 22
    [3] DISASSEMBLY/ASSEMBLY [3]-12. Laser Mechanism (for LS1016L only) DISASSEMBLING Note: Makita-operated or authorized repair shops do maintenance of Laser mechanism. 1) As shown in Fig. 13, remove 4x18 Tapping screw and Lead cover holder. Then disconnect Connectors of Laser circuit from that of
  • Makita LS1016 | Technical Reference - Page 23
    . 70 approx.10mm Fig. 71 Leaf spring Rack block Slide pipe Grip 50 Turn base Cap Slide lock plate Bind CT4x12 Tapping screw [4]-2. Lower fence and Upper fence 1) Put Lower fence R on Guide fence. Install Upper fence R complete to Lower fence R and then fasten them by turning Lever 45. (Fig
  • Makita LS1016 | Technical Reference - Page 24
    adjustment of the right angle between Blade and Guide fence using 1R208. 3) Tighten M8x25 Hex socket head bolt (4pcs.) in order 1, 2, 3, and 4. without moving any parts. (Fig. 73) Fig. 73 Pretighten M8x25 Hex socket head bolt 1 2 3 4 Guide plate 1R208 Blade [4]-4. Blade Use 1R208 and M8x20
  • Makita LS1016 | Technical Reference - Page 25
    (Part No. 253771-0) Fig. 85 M5x24 Thumb screw 1R315 M10x20 Hex flange head bolt Fig. 86 Switch for laser Operation switch M4x6 Hex socket set screw B Laser cover 1R315 M4x6 Hex socket set screw A Bring the laser beam near this groove. Bring the laser beam near this groove. 1R315 9) Slide
  • Makita LS1016 | Technical Reference - Page 26
    set screw B for adjusting the laser beam against Fence Fig. 88 M4x6 Hex socket set screw A for adjusting the laser beam against Base Cut 35mm length These portions of the old versions 1R315 are stuck on Pan head screw that is secured Bearing box for LS1016L. Therefore, they are not used for
  • Makita LS1016 | Technical Reference - Page 27
    Motor housing Choke coil Field (viewed from Armature gear side) Brush holder of Dust nozzle side Controller Terminal block Blue is used for some countries. COM NC Main Switch for switch protection of brake coil Laser switch unit Insulated terminal Laser section exclusively for LS1016L
  • Makita LS1016 | Technical Reference - Page 28
    P 28/ 37 Motor housing Brush holder of Handle side Field (viewed from Armature gear side) Brush holder of Dust nozzle side Terminal block Handle cover and Handle section Main switch Controller Insulated terminal Line filter Laser section exclusively for LS1016L Laser switch unit Circuit
  • Makita LS1016 | Technical Reference - Page 29
    side Switch for protection of brake coil Brake switch Motor housing Brush holder of Dust nozzle side Field Controller Terminal block COM NC Main switch Insulated terminal Laser switch unit Laser section exclusively for LS1016L Circuit plate Transformer Handle cover and Handle section
  • Makita LS1016 | Technical Reference - Page 30
    protection of brake coil Motor housing Brush holder of Dust nozzle side Field (viewed from Armature gear side) Blue is used for some countries. Insulated terminal Controller COM NC Main switch Laser switch unit Insulated terminal Laser section exclusively for LS1016L Circuit plate Brown is
  • Makita LS1016 | Technical Reference - Page 31
    ) Brush holder of Dust nozzle side Insulated terminal Blue is used for some countries. Handle cover and Handle section Main switch Controller Insulated terminal Laser switch unit Laser section exclusively for LS1016L Circuit plate Transformer Blade case Laser circuit Power supply circuit
  • Makita LS1016 | Technical Reference - Page 32
    Wiring diagram Wiring around Case of LS1016L Fig. D-3 Inside of Case Outside of Case P 32/ 37 Case . D-4 Bottom view of Handle Lead cover holder Connector of Power supply circuit Rib Connector of Laser circuit Fix Lead wires (blue) with Lead wire holder. Top view of Handle Pass the
  • Makita LS1016 | Technical Reference - Page 33
    route Field lead wires * (black) (white and purple) between * (yellow) Armature and Baffle plate. case of Power rib for Laser supply circuit switch unit Pass the Lead wires from Motor housing through this notch of Handle. Pass Lead wires through ribs as illustrated. Do not put Lead wires on
  • Makita LS1016 | Technical Reference - Page 34
    route Field lead wires (white and purple) between * (black) * (yellow) Armature and Baffle plate. Case of Power ribs for Laser supply circuit switch unit Pass Lead wires from Motor housing through the notch of Handle. Pass Lead wires through ribs as illustrated. Do not put their Lead wires on
  • Makita LS1016 | Technical Reference - Page 35
    127V area other than UK Field lead wires have to be tightened in Motor housing so as not to touch Armature. Insulated Terminal Do not put Lead wires on these ribs. Controller Field Lead wires * (orange) rib * (black) * (yellow) Case of Power ribs for Laser Supply Circuit switch unit Pass
  • Makita LS1016 | Technical Reference - Page 36
    Wiring in Motor housing and Handle for UK 110V P 36/ 37 Field lead wires have to be tightened in the Motor housing so as not to touch Armature. Terminal block Do not put Lead wires on ribs. Controller Field lead wires rib * (orange) * (black) * (yellow) case of Power ribs for Laser supply
  • Makita LS1016 | Technical Reference - Page 37
    Wiring diagram Fig. D-5 Wiring of Laser circuit complete of LS1016L for all countries Pay attention not to pinch Lead wires between ribs of Blade case designated in gray color and Lead cover. P 37/ 37 Route the Lead wires of Laser circuit complete Boss between Rib C and Boss. [Blade case after
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
PRODUCT
P 1/
37
Models No.
Description
C
ONCEPT AND MAIN APPLICATIONS
S
pecification
LS1016, LS1016L
Slide Compound Miter Saw 255mm (10")
*1
/ 260mm (10-1/4")
[*1
255mm (1") for North America
]
LS1016 and LS1016L are upgraded sister tools of
LS1013 series models,
featuring DXT (Deep eXact cutting Technology) achieved by our consistent
pursuit of cutting larger size workpiece but with higher accuracy.
The features and benefits of DXT are:
Deep cutting
3-Stage reduction gear unit and Movable rear blade guard provide
larger capacities of cutting Crown molding and Baseboard (Skirt board)
which are typical workpieces of slide compound miter saws.
eXact cutting
Precise and exact cutting obtained by employing:
Double sliding mechanism
Double sliding guide fence
Quick and accurate miter angle lock, etc
LS1016L additionally features laser marker for easy cut line alignment.
T
ECHNICAL INFORMATION
No load speed: min-
1
= rpm
Double insulation
Diameter
Hole diameter
Protection against electric shock
Cord length: m (ft)
Net weight
*3
: kg (lbs)
Lock-off switch
Electric brake
Electronic
control
Soft start
Constant speed
Saw blade:
mm (")
Yes
Yes
Yes
Yes
Laser marker
Yes
No
3,200
250 (9-7/8) - 260 (10-1/4)
European countries: 30,
North America: 15.88 (5/8), Other countries: 25.4 (1)
2.5 (8.2)
23.6 (52.0)
23.7 (52.2)
Net weight
*2
: kg (lbs)
24.1 (53.1)
24.2 (53.3)
S
tandard equipment
O
ptional accessories
Note:
The standard equipment for the tool shown may differ by country.
Vertical vise
...............................
1
TCT saw blade
..........................
1
Dust bag
....................................
1
Socket wrench 13
.......................
1
Triangular rule
...........................
1
Spare lock-off button
..................
2
Holder set
...................................
2 (all countries except North America)
Hex wrench
................................
1 (LS1016L only)
Horizontal vise
Dust box
TCT saw blades
Portable miter saw stand
Crown molding stopper set
Dimensions: mm (")
Width (W)
Height (H)
Length (L)
718 (28-1/4)
671 (26-1/2)
640 (25-1/4)
L
W
H
120
110
220
230
240
15
1,510
---
900
2,600
50/60
7.2
1,510
800
2,000
50/60
6.9
1,510
800
2,000
50/60
6.6
1,510
800
2,000
50/60
15
900
2,600
50/60
Continuous Rating (W)
Voltage (V)
Cycle (Hz)
Input
Output
Max. Output (W)
Current (A)
*2
Weight according to EPTA-Procedure 01/2003, with
TCT
saw blade and "Blocking mechanism at the rest position"
*3
With TCT saw blade, without "Blocking mechanism at the rest position"
See next page for the cutting capacities.
Model No.
LS1016
LS1016L
Specification