Marantz PM6004 User Manual - Page 18

Specifications, Index, Explanation terms - driving two sets of speakers

Get Marantz PM6004 PDF manuals and user guides View all Marantz PM6004 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

ENGLISH Specifications Explanation terms Index • RMS Power output (20 Hz - 20 kHz simultaneous drive of both channels): • Total harmonic distortion (20 Hz - 20 kHz simultaneous drive of both channels, 8 Ω load): • Output band width (8 Ω load, 0.06%): • Frequency response (CD, 1 W, 8 Ω load): • Dumping factor (8 Ω load, 40 Hz - 20 kHz): • Input sensitivity/Input impedance PHONO (MM): CD, TUNER, AUX/DVD, RECORDER: • Maximum allowable PHONO input level (1 kHz) MM: • RIAA deviation (20 Hz - 20 kHz): • S/N (IHF-A, 8 Ω load) PHONO (MM): CD, TUNER, AUX/DVD, RECORDER: • Tone control Bass (50 Hz): Treble (15 kHz): • Power requirement: • Power consumption (UL60065): • Power consumption during standby: • Weight: 45 W x 2 (8 Ω load) 60 W x 2 (4 Ω load) 0.08 % 10 Hz - 50 kHz 10 Hz - 70 kHz +0 dB, -1 dB 100 2.2 mV/47 kΩ 200 mV/20 kΩ 100 mV ±1.0 dB 83 dB (5 mV input, 1 W output) 102 dB (2 V input, Rated output) ±10 dB ±10 dB AC 120 V 60 Hz 150 W 0.2 W 7.4 kg (16 lbs 5 oz) zzFor the purpose of improvement, the specifications and design are subject to change without notice. P Protection Circuit This is a function to prevent damage to components within the power supply when an abnormality such as an overload or excess voltage occurs for any reason. In this unit, the power indicator blinks and the unit enters standby mode when an abnormality occurs. S Speaker impedance This is certain-rated resistance of the speaker set to an alternating current and expressed in ohms. The smaller the impedance, the greater the output. However, load on the amplifier is increased. Use speakers whose impedance is supported by this unit. vvA Adjusting the tone 9 Adjusting the volume 9 Auto standby mode 12 vvB BALANCE 4, 8 BASS 4, 8 Batteries 3 vvC Connection Connecting cables 6 Connecting players 7 Connecting recorders 7 Connecting the speakers 6, 7 vvI INPUT SELECTOR 4, 8 vvM Mute 4, 8 vvP Power cord 8 Protection circuit 6, 14 vvR Remote control 3, 5, 10, 11 vvS SOURCE DIRECT 4, 8 Speaker cables 6, 7 Speaker impedance 7, 14 Stereo pin-plug cable 6 vvT TREBLE 4, 8 vvV VOLUME 4, 8 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
14
ENGLISH
•
RMS Power output
(20 Hz – 20 kHz simultaneous drive of both channels):
45 W x 2 (8 Ω load)
60 W x 2 (4 Ω load)
•
Total harmonic distortion
(20 Hz – 20 kHz simultaneous drive of both channels, 8 Ω load):
0.08 %
•
Output band width
(8 Ω load, 0.06%):
10 Hz – 50 kHz
•
Frequency response
(CD, 1 W, 8 Ω load):
10 Hz – 70 kHz +0 dB, -1 dB
•
Dumping factor
(8 Ω load, 40 Hz – 20 kHz):
100
•
Input sensitivity/Input impedance
PHONO (MM):
2.2 mV/47 kΩ
CD, TUNER, AUX/DVD, RECORDER:
200 mV/20 kΩ
•
Maximum allowable PHONO input level
(1 kHz)
MM:
100 mV
•
RIAA deviation
(20 Hz – 20 kHz):
±1.0 dB
•
S/N
(IHF-A, 8 Ω load)
PHONO (MM):
83 dB (5 mV input, 1 W output)
CD, TUNER, AUX/DVD, RECORDER:
102 dB (2 V input, Rated output)
•
Tone control
Bass (50 Hz):
±10 dB
Treble (15 kHz):
±10 dB
•
Power requirement
:
AC 120 V 60 Hz
•
Power consumption
(UL60065):
150 W
•
Power consumption during standby
:
0.2 W
•
Weight:
7.4 kg (16 lbs 5 oz)
z
For the purpose of improvement, the specifications and design are subject to change without notice.
Specifications
Index
v
A
Adjusting the tone ················································ 9
Adjusting the volume ··········································· 9
Auto standby mode ············································ 12
v
B
BALANCE ························································· 4, 8
BASS ································································ 4, 8
Batteries ······························································· 3
v
C
Connection
Connecting cables ············································· 6
Connecting players ············································ 7
Connecting recorders ········································ 7
Connecting the speakers ······························· 6, 7
v
I
INPUT SELECTOR············································4, 8
v
M
Mute································································· 4, 8
v
P
Power cord ··························································· 8
Protection circuit ············································ 6, 14
v
R
Remote control ···································· 3, 5, 10, 11
v
S
SOURCE DIRECT ············································· 4, 8
Speaker cables ················································· 6, 7
Speaker impedance········································7, 14
Stereo pin-plug cable············································6
v
T
TREBLE ···························································· 4, 8
v
V
VOLUME ·························································· 4, 8
P
Protection Circuit
This is a function to prevent damage to components
within the power supply when an abnormality such
as an overload or excess voltage occurs for any
reason.
In this unit, the power indicator blinks and the unit
enters standby mode when an abnormality occurs.
S
Speaker impedance
This is certain-rated resistance of the speaker set
to an alternating current and expressed in ohms.
The smaller the impedance, the greater the output.
However, load on the amplifier is increased. Use
speakers whose impedance is supported by this
unit.
Explanation terms